SailNet Community - Reply to Topic

   Search Sailnet:

 forums  store  


Quick Menu
Forums           
Articles          
Galleries        
Boat Reviews  
Classifieds     
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Charts
Clothing
Electrical
Electronics
Engine
Hatches and Portlights
Interior And Galley
Maintenance
Marine Electronics
Navigation
Other Items
Plumbing and Pumps
Rigging
Safety
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here






Go Back   SailNet Community > On Board > Gear & Maintenance > chain splicing
 Not a Member? 


Thread: chain splicing Reply to Thread
Title:
  

By choosing to post the reply below you agree to the rules you agreed to when joining Sailnet.
Click Here to view those rules.

Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Topic Review (Newest First)
01-25-2003 03:42 AM
CaptGentry
chain splicing

If you are sending that splice into a deckpipe I would add a chaf guard to the splice. Some 2" heat shrink or some rawhide.
01-24-2003 06:13 AM
sailorman10
chain splicing

After a little experimentation, I worked out the splicing process adequately enough. I wove the strands thru each link for about a foot and then turned and wove back thru the links to the chain end. Upon reaching the rope, I put in a long splice with about 7 tucks and finished off with the appropriate whipping. On my experimental piece, I tested it to failure with a 4 ton come-a-long between two trees. The splice held very well and the ulitmate failure was in the rope, not the splice. This type splice probably doesn''t make a stronger splice but it should reduce chafe as the load is spread out over several links instead of just one.

Randy
01-21-2003 10:11 AM
thefantasea
chain splicing

New England Rope has a "Contact Us" button on their website. It''s primary use is to request literature (including a splicing guide) but there is also a box for including comments. Why not pose the question to them?
01-21-2003 09:48 AM
sailorman10
chain splicing

The splice on New England Ropes site is for an single link splice in the last link. I can do this splice with no problems however, What I am looking for is illustration or description of a splice into the last several links.

Randy
01-21-2003 08:11 AM
ikent
chain splicing

The New England Ropes site has instructions for a rope to chain splice. Brion Toss''s Riggers Apprentice also shows another version.

Best of luck,
Ike
01-21-2003 08:09 AM
sailorman10
chain splicing

That is the setup I am using now. However, I am installing a deckpipe to store the rode below decks instead of in a canvas bag. The thimble setup will not pass thru the pipe.

Randy
01-21-2003 07:21 AM
maestro
chain splicing

how about using a thimble and creating a permanent loop in the line. Then using a stainless shackle to connect the two together??
01-21-2003 07:02 AM
sailorman10
chain splicing

Ok, I have exhausted my search capabilities on the internet and realized I would have to turn to the real experts. I need to splice my 3 strand nylon rode onto a length of chain for the anchor. I have read that splicing onto only the last link of chain could would put more stress on the fibers due to the tight radius of the turn around the link and that a splice over the last several links is better/stronger. However, I cannot find any detail or instruction on making this type of splice. Does anyone out there know how to do this? I could cobble together a splice but would rather do it right since my boat will be riding on this splice. Any suggestions?

Randy

 
Posting Rules
You may post new threads
You may post replies
You may post attachments
You may edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On


All times are GMT -4. The time now is 02:32 AM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) Marine.com LLC 2000-2012

The SailNet.com store is owned and operated by a company independent of the SailNet.com forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.