|Topic Review (Newest First)|
|10-13-2011 09:54 AM|
Lockley Sea Witch repairs
I recently purchased a 12' Lockley Sea Witch for my scouting kids. $270 with trailer can't go wrong. Very sailable but that outer plastic skin has many cracks and dimples. Some cracks wrap from gunwales down toward keel. These certainly let in water to the foam but won't let it sink. The worst issue is cracking of the inner/top surface around the dagger board. It is split down to the footwell and allows water to seep in rather quickly.
I am in the process of repairing that and the entire hull in my own method. I am routing-out all the cracks and cracked dimples far and wide enough to allow filling with Bondo-Hair fiberglass filler. I have completed some of the filling. Plently more to route-out and fill. Then I will sand them all down to as close to flush as possible. Sand entire hull, and paint top and bottom with a gloss spray paint made for adhesion to plastic.
Keep in mind I have no fiberglass repair experience (or plastic) but it appears this will stabilize any of the current hull cracks and keep more water from infiltrating into the foam.
|05-23-2010 08:11 PM|
Repairs on Lockley Sea Witch, Castlecraft Sunflower
I'm definitely not an expert but I have a Sea Witch with red ABS skin over Styrofoam core. I had a Castlecraft Sunflower II years ago which was the same design, a little smaller and a lot cheerier shade of yellow!
A few big bumps and the 30-year old ABS shows it's age by fractures.
With the previous info in mind of avoiding any kind of volatile chemicals which will quickly destroy the foam core I have successfully repaired these boats using URETHANE adhesives and FOAM. It sticks to about anything, right?
Though it doesn't hold up to UV exposure it works fine for repairs under the ABS and repairs like remounting the bump trim, etc.
FYI, I am into boats to make them sail- sometimes they don't LOOK like the top-of-the-line craft but I'm in it for FUN !
Anyone else tried this?
|01-14-2008 09:04 AM|
|JoesBlues||Thanks so much. I'll soon be hard at work.|
|01-12-2008 02:51 PM|
Here is repair info for Snark which is same construction:
HULL REPAIRS : use two part epoxy cement for all repairs or reattaching rub rail. Obtain locally May use epoxy cement or automotive epoxy fillers. For large areas you may use fiberglass repair kits. All above locally available.
DO NOT USE ANY PRODUCT CONTAINING PETROLEUM BASES.
DO NOT USE FIBERGLASS KITS WITH POLYESTER RESINS.
WEST SYSTEMS Epoxy coatings can be found at
Painting ABS - Most enamel paints will adhere to ABS. Use several light coats. Test paint in a small spot first.
DO NOT GET ANY PAINT ON ANY PART OF EXPOSED FOAM - IT WILL DISSOLVE IT.
Painting Sea Snarks - This all foam boat can be fiber glassed, obtain materials locally. Any petroleum based paint will dissolve the foam.
DO NOT USE PETROLEUM BASED PAINTS DIRECTLY ON FOAM
|01-12-2008 12:33 PM|
There are a lot of plastics out there.
I have done a couple of repairs on cracks.
I took a little piece to a local Plexiglas (I will just call it that) fabricator.
I found which solvent they sell that melts it.
I scraped, cut, or otherwise collected some of the plastic and mixed it with the solvent to create a "glue-like" consistency.
I put it on the pieces and "glued" them back together.
Good luck finding.
1. the right solvent.
2. the same, exact plastic - manufacturer scrap??
I did not need much so I actually found it on the faring in the form of molding ports - you know, extra points etc that things have when the molding is done - whatever you call it.
Then there was another plastic and the "good" (I thought) solvent would not melt it - had to get another kind. Expensive and VERY volatile.
Short working time too!!
IMO epoxy will not stick to plastic.
Maybe the Mfgr will give you a hint?
|01-12-2008 09:48 AM|
|JoesBlues||Ok...Thanks for the info. I think I'm going to try to epoxy over it and See what happens. Worst case the epoxy wont bind well and then I'll have a female mold of the hull...right?? lol|
|01-11-2008 10:42 PM|
Sorry, I've fixed cored fibreglass, but not foam core plastic laminate. How you fix the gouges would depend on the composition of the plastic and whether glass will stick to it. If possible (and on general principles), if you can determine what the original plastic is, patch it with that if you can melt it on without setting fire to the foam core, and then sand it down or simply shape it with a razor.
For $400, you can afford to experiment. Roughing up the surface and having a crack with thickened epoxy is worth a try, but I bet the epoxy is considerably denser than the plastic and might fall off.
If that doesn't work, try gluing rubber or PVC patches on with contact cement, and paint the outside so it doesn't show.
But seriously, I don't have a clue what you boat is made of (there's dozens of structural plastics in general use) and the potential for making it worse is strong.
|01-11-2008 09:03 PM|
|JoesBlues||Nobody can help??|
|01-09-2008 01:57 PM|
Lockley Sea Witch Repairs
Hey All, new member here with a question. I don't know if this belongs in the maintenance area, if so mods please move. Ok -
I purchased a Lockley Sea Witch on E-bay for 400 dollars. In hindsight it might have been a poor purchase, however I should have gone and looked at the boat before buying. Anyway, the boat is plastic, with closed cell foam about 2-3" thick, followed by another layer of plastic for the inside. There are several LARGE gouges in the plastic that are cutting into the foam and the seller repaired with what looks like injectable foam. (very ugly yellow color) The boat will sail, however I want to clean it up and make it a nice dinghy for myself and my family. Question is this, can you put glass over the existing plasic hull? My plan was to sand the plastic with coarse sandpaper, apply several layers of alternate mat and roven woving, while filling and fairing the areas that were gouged out. Do you thing the epoxy will bond to the plastic? Would it be better to take off the plastic and bond to the foam (is that possible) Any other methods that would work better than what I mentioned? Any help is much much appreciated. I plan on taking pictures of the process and making a blog out of it. It will give me something to keep me busy during the winter. Once again thanks to anyone who can help.