|Topic Review (Newest First)|
|03-18-2013 10:32 AM|
Re: Big Black Port Gaskets
I know this is an old post but I just bought a 72 Morgan OI that need the same gaskets replaced can you tell me where to order everything from?
|06-14-2012 12:40 AM|
Re: Big Black Port Gaskets
Originally Posted by CaptainForce View Post
Those ports have always struck me as being weak for offshore use. If I were doing an ocean crossing, I might pull the windows and gaskets out, and bolt pieces of Lexan over the openings, caulked to the hull.
I suspect that would be a heck of a lot more work than it sounds like.
Thanks for the post -- I may replace my own leaking-black-stripes-down-the-topsides gaskets, now.
Charles / Right Galah
|01-09-2012 03:16 AM|
Morgan O/I 41 Port Gasket
Originally Posted by Orionsue View Post
I have an O/I 41 in Fajardo, PR with the same leaky port problem that you have. Wanted to find out how you came out with the Stanlock gaskets.
|02-18-2009 10:12 PM|
|CaptainForce||The gaskets referred to in the posts above call for a 1/4 inch portlight. I've used the Lexan polycarbonate plastic which was cut with a saw and sanded. 'good luck with the project, Aythya crew|
|02-06-2009 05:04 PM|
I just got the gasket in yesterday.....What type of glass did you use Plexi/Lexan/Acrylic and what thickness did you go with I have been to two diffrent stores and none of the people working there have heard of Marine grade glass. Is there such a thing?
Last but not least did you cut the glass with a hot knife or did you cut it with a jigsaw and round out the edges with a sander?
I can't wait to start this project I think it will make my boat look like a million dollars when it is all set and done.
|01-19-2009 03:35 PM|
|ashatsea||Just bought a pair of ring pliers from Lowes for $18 my boat is in the water I'm hoping it won't be to difficult to do this laying on my stomach.|
|01-13-2009 02:44 PM|
|CaptainForce||Matt, Thanks for that "ring" pliers idea. I have to admit that I worked very hard with the finger stress to complete my eight ports below the toe rail. I still haven't taken on the the four higher portlights in my aft cabin. When I do, I'll have the pliers. Stewart|
|01-11-2009 08:34 PM|
Don't forget the ring pliers!!!!
I tried to force that locking strip in with the marlin spike. My thumbs went numb for several weeks. After an hour I had 6" of locking strip installed. I trimmed off the excess and went home.
The pliers open up the gasket and it slides right in, sort of. It still takes some work. It took about an hour to finish the rest of the port.
|01-08-2009 06:36 PM|
|ashatsea||Thanks again I found a place locally in St. Pete for replacement windows and I will be ordering the gaskets and lock strip shortly..|
|01-05-2009 09:10 PM|
Ashatsea, The invoice I have for the gaskets is the Stanlock product pruchased from Griffith Rubber Mills, P.O.Box 10066, Portland, Or. 97296, Phone= (503) 226-6971.
The item # for the gasket is 31513SL with the description SL-2026 1/4 x 1
The item # for the locking strip is 37653FTSL with the description
SL-1250 Lock Strip
As you read in the above postings, the gasket replaces the original well, but there is difficulty in applying the locking strip within the 3" radius turns at the ends of the portlights.
Here are views of my portlights before and after:
'take care and joy, Aythya crew
|This thread has more than 10 replies. Click here to review the whole thread.|