SailNet Community - Reply to Topic
Thread: Brand new bilge pump that doesn't pump.... ugh Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.

User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

  Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below

  Topic Review (Newest First)
02-08-2008 08:26 PM
Lancer28 Awesome input guys, I would have never thought to look for a anti-siphon valve or whatever it is called.

I'll look into the amperage and voltage while I'm in there.

I'll touch base back here when I get the entire line checked and the power measured.. Heck, its a good excuse (for me to justify to the wife) to replace the older hose and electrical wires anyhow.

Thanks again
02-04-2008 07:05 PM
sailingdog Matt-

What you're thinking of is called a check valve, and they're usually a really bad idea on a bilge pump, since the add quite a bit of back pressure and really reduce the pump's output capacity.
02-04-2008 12:19 PM
MattGardner This: " If I unclip the pump from the screen / mount and shake it, then the air bubbles slurp out of the hose and then it starts flowing"
...makes me wonder if there a backflow preventer on your bilge hose? If so it can trap a pocket of air that will compress below the (however many feet of) water in the bilge hose that will prevent the pump from working correctly.
02-04-2008 07:55 AM
trantor12020 Is your bilge clean? I know my Rule pump would have problem if my bilge is dirty with fibre, hair small pieces of small something. I even end up removing the strainer wire and cleaning the sloted base (red color bottom that mount on the bilge) before it would work.
02-03-2008 09:14 PM
sailingdog Have you checked how much voltage the pump is getting and how much current it is drawing. Maybe the motor on the pump is shot or it is drawing too little current to work properly. Either condition might leave the pump so that it can't self-prime properly. It could also just be a bad pump.
02-03-2008 01:14 PM
k1vsk Don't understand your statement that even a "rule self-priming pump isn't helping." All bilge pumps are self-priming so the q becomes with what are you comparing it?
There are only two reasons why a bilge pump won't work - too much head for the pump or a leak. What size pump are you using?
02-03-2008 11:27 AM
Brand new bilge pump that doesn't pump.... ugh

I've got a second issue today too. This one is stumping me.

I've got a brand new bilge pump installed and it takes 10-15 minutes of run time to re-prime it and get the water flowing out of the bilge each time I start it. Heck, sometimes it won’t prime and start to flow at all.

If I unclip the pump from the screen / mount and shake it, then the air bubbles slurp out of the hose and then it starts flowing. I've narrowed it to some sort of reverse-drain out of the bilge line to the overboard outlet, but even a rule self-priming pump isn't helping... ugh.

Obviously, I can't be below decks every time I need to run the pump to shake it to get started. The lift on the pump is only about 4 feet, and about 8-10 feet in length.

Is there anyway to resolve this - I've run out of ideas (well, besides scrapping it for a manual diaphragm pump I can run from the cockpit). I've replaced the hosing and pump, and I still haven't found a way to get the water out without dicking around with the pump itself each time it needs to run. The battery drain is a bear to deal with, notwithstanding the initial issue….

Some thoughts here would be GREATLY appreciated!!!!

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

For the best viewing experience please update your browser to Google Chrome