SailNet Community - Reply to Topic

   Search Sailnet:

 forums  store  


Quick Menu
Forums           
Articles          
Galleries        
Boat Reviews  
Classifieds     
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Charts
Clothing
Electrical
Electronics
Engine
Hatches and Portlights
Interior And Galley
Maintenance
Marine Electronics
Navigation
Other Items
Plumbing and Pumps
Rigging
Safety
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here






Go Back   SailNet Community > On Board > Gear & Maintenance > Wire tube in mast
 Not a Member? 


Thread: Wire tube in mast Reply to Thread
Title:
  

By choosing to post the reply below you agree to the rules you agreed to when joining Sailnet.
Click Here to view those rules.

Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Topic Review (Newest First)
03-26-2001 07:50 PM
noctaluca
Wire tube in mast

To instal a conduit tube up mast:
Use at least 1" PVC tube. I ran large vhf radio wire, and two, three stranded cables up to masthead. This almost maxed the 1" tube out. Electrical conduit with "shouldered" connections work best instead of "sprinkler" PVC with connections, because the junctions lye closer to the mast. This may be important if you happen to need a rivet at that particular point. Measure where these joints are and try not to rivet there. You may put the conduit on whatever corner of the mast you need. Leave about a foot from the top and bottom, don''t run it too far up. To secure the conduit to mast drill two holes side bye side, about and inch an a half apart. One hole is for the rivet, the other for a stiff wire, such as welding rod, to hook under the conduit and pull it to the other hole for riveting. Plug the extra hole with a rivet when done. Also figure out what length rivet best suits the purpose. I used too long of rivets and it reduced the volume of the tube.
This job on my 42 foot mast took me 3 hours with another person to help. It is well worth doing especially if you intend on internal halyards in the future. Good luck and e-mail me direct if you need more details.
Bill 8-)

03-25-2001 04:01 PM
jrd22
Wire tube in mast

We redid ours(went to larger PVC to accomodate more wires) but only riveted in four spots like the original. Remember to run your strings for all the different openings before installing in mast. Try running maximum number of wires through pipe to allow for lots of room, we were surprised how large we had to go.
03-11-2001 07:14 AM
navtron
Wire tube in mast

I did it on my Newport 30 mklll..Mast 40''
On front of mast, to one side or other, drill small holes 2-3 feet apart up mast.Then put the mast with holes facing down and install lite weight maybe 3/4"-1'' pvc tubing.
Again now drill holes in the pvc thru the previous holes and rivet the pvc in(rivets are Aluminium)...Leave an opening for various things in mast on the way up so wire can be feed out to them. This came standard on the Newport and I redid it 14 years later....Sailed to Bermuda, Bahamas, East Coast offshore during those times...
03-09-2001 04:40 PM
loki
Wire tube in mast

I want to install a tube in my 40 ft. mast to contain all of the wires leading up to the masthead-they currently hang free. Does anyone have experience with attaching the tube to the mast eg. mechanical fastners, epoxy, calk. Any sugestions will be much appreciated.

 
Posting Rules
You may post new threads
You may post replies
You may post attachments
You may edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On


All times are GMT -4. The time now is 12:42 PM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) Marine.com LLC 2000-2012

The SailNet.com store is owned and operated by a company independent of the SailNet.com forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.