SailNet Community - Reply to Topic

   Search Sailnet:

 forums  store  


Quick Menu
Forums           
Articles          
Galleries        
Boat Reviews  
Classifieds     
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Charts
Clothing
Electrical
Electronics
Engine
Hatches and Portlights
Interior And Galley
Maintenance
Marine Electronics
Navigation
Other Items
Plumbing and Pumps
Rigging
Safety
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here






Go Back   SailNet Community > On Board > Gear & Maintenance > Deck hardware
 Not a Member? 


Thread: Deck hardware Reply to Thread
Title:
  

By choosing to post the reply below you agree to the rules you agreed to when joining Sailnet.
Click Here to view those rules.

Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Topic Review (Newest First)
07-29-2003 12:10 PM
Thermal
Deck hardware

If the holes are in the same place and the right size and not damaged, they could be reused and sealed with 4200 - BUT, I get the impression that you are talking about screws, and not bolts that go all the way through, in which case you must go the epoxy repair route. I would''nt feel comfortable having that fitting attached with screws and replace them with through bolts and a backing plate. There was a good article by Don Casey about holes in the deck, can''t seem to find it on the sailnet site, but you can see it at http://www.boatus.com/boattech/casey/39.htm
07-28-2003 10:46 AM
soapstone
Deck hardware

Hate to disagree- but I once owned a boat that the previuos owner used 5200 on.. Had core rot everyplace that the 5200 had dried up and leaked.

I suggest using the epoxy method described above. But go further, bend a nail into an "L" shape and gouge out a hollow with a power drill in your coring to create a washer of sorts. Then fill the hollow with thickened epoxy. It will also take the load better.

Dave
07-26-2003 02:52 AM
GordMay
Deck hardware

A note to the "4200" Fan-Club.
The quickest & easiest way is seldom the best way.
Remember, if you don''t have time to do it right in the first place - where will you get the time to fix it?
If the existing holes, and the surrounding solid fibreglass are in good shape (no spauling, no hole elongation etc), overdrill the exit''g holes and epoxy, then re-drill to size. "4200" can (then) be applied as a deck sealant.
All rig fastenings should be "backed".
OMO
Gord
07-25-2003 01:13 PM
natejount
Deck hardware

that''s exactly what i''m doing, I will go and grab some of that 4200. I''m assuming it''s the type of stuff I''ll need a caulking gun for...Another stupid deck hardware question...should I use the exact same holes that the original screws were in...i.e. unsrew the old hardware, put this marine adhesive in there, let it cure, then drill back through the same hole locations? or, since this is a swivel, so the holes will be a square about 1.5 in. apaqart from one another, should I drill new holes around the circumference of the same circle?
07-25-2003 12:28 PM
mikehoyt
Deck hardware

Then there is the quicker less permanent method. Use 3M 4200 to fill in old holes and seal the new ones. This is assuming that you are replacing with a similar block in the same location. Use fast cure and it will be fully set in 24 hrs and you can probably use it in 12.

Mike
07-25-2003 10:13 AM
RichH
Deck hardware

Use epoxy filled with colloidal silica powder. Use an epoxy catalyst that matches the ambient heat range, let cure (48+ hours), then heat the repair with a heat gun (without burning the repair/gel coat etc.) to complete the cure. Then redrill.
Go to the "WEST System" site for specific details: www.gougeon.com/ or www.westsystem.com
07-25-2003 09:43 AM
natejount
Deck hardware

Come on now people. You are telling me that no one has replaced a block on a fiberglass deck. What do i need to use to fill the holes before I redrill.?
07-24-2003 12:03 PM
natejount
Deck hardware

sorry, work interuptted me and I didn''t finish. The swivel block and pulley is one of my main sheet blocks on top of my cockpit (i don''t have main gear with a traveler, etc.)
07-24-2003 12:03 PM
natejount
Deck hardware

sorry, work interuptted me and I didn''t finish. The swivel block and pulley is one of my main sheet blocks on top of my cockpit (i don''t have main gear with a traveler, etc.)
07-24-2003 12:01 PM
natejount
Deck hardware

I have never had to change deck hardware, but I have a swivel block with pulley contraption that is my main that I need to replace, and I do not want to mess anything up.

Exactly what types of silicon, glue, or whatever do I need to plug the holes after I take the old gear off, and how long until I can drill back into it?

 
Posting Rules
You may post new threads
You may post replies
You may post attachments
You may edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On


All times are GMT -4. The time now is 04:21 AM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) Marine.com LLC 2000-2012

The SailNet.com store is owned and operated by a company independent of the SailNet.com forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.