SailNet Community - Reply to Topic

   Search Sailnet:

 forums  store  


Quick Menu
Forums           
Articles          
Galleries        
Boat Reviews  
Classifieds     
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Charts
Clothing
Electrical
Electronics
Engine
Hatches and Portlights
Interior And Galley
Maintenance
Marine Electronics
Navigation
Other Items
Plumbing and Pumps
Rigging
Safety
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here






Go Back   SailNet Community > On Board > Gear & Maintenance > rebedding stanchions
 Not a Member? 


Thread: rebedding stanchions Reply to Thread
Title:
  

By choosing to post the reply below you agree to the rules you agreed to when joining Sailnet.
Click Here to view those rules.

Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Topic Review (Newest First)
06-10-2008 02:20 AM
merttan Screwed in stanchions = screwed sailor... Sorry couldn't stop myself...
I'm going to rebed mine soon... The safest way is to get a don casey book to read through... Use the widest possible backing plates possible to avoid stress cracks around the base since when you need them, you really need them...
06-09-2008 09:11 PM
fullkeel7 For better under deck access with a cordless, use an extension or one of those flexible ones that fit the drive (1/4, 3/8 or 1/2 inch) of your cordless and your universal 6 point deep well socket. That way there is no need to have access inside tight spots for the cordless.
06-09-2008 09:02 PM
Maine Sail
Quote:
Originally Posted by Freesail99 View Post
The key word here is access permitting. As far as using a rechargeable impact driver, good luck in keeping the screw driver in the slot on the bolt, up top. Most of the bolts have a slotted head.
I do this from under the deck on the nuts not from the top on the screws. So far, with ratchet extensions and or knuckles, I have been able to reach each and every stanchion base on my boat and re-bed every single one with only the impact driver and no screw driver or wrench is used on deck..

The whole point of me using the impact driver is it makes it an easy one person job without having to use Gorilla Tape and a pair of Vise Grips...

BTW if an impact driver will not fit, a pair of needle nose Vise Grips and Gorilla Tape will. Simply taping the vise grips to the underside of the deck, clamping the nut, with this tenacious tape has worked every single time for me.. Quick and easy but not as quick and easy as an impact driver..
06-09-2008 08:27 PM
Freesail99 The key word here is access permitting. As far as using a rechargeable impact driver, good luck in keeping the screw driver in the slot on the bolt, up top. Most of the bolts have a slotted head.
06-09-2008 07:54 PM
Maine Sail
Guys..

This job can be done most of the time, access permitting, from bellow deck with a rechargeable impact driver!

I have re-bedded LOTS of fittings solo with my simple and inexpensive Ryobi 18v impact driver. Honestly it works like magic! Brrrr, brrrr, brrrr and the nut comes off with no wrench or screw driver being used on the deck level! Brrrr, brrrr, brrrr and the nut goes back on with no wrench or screw driver on the deck side.. Be careful because with some of these it's very easy to over torque and snap a bolt clean off. The "IMPACT" effect allows you to tighten from one side in most cases..


Or a slightly higher quality tool with a lifetime warranty:
06-09-2008 06:56 PM
knothead
Quote:
Originally Posted by rheaton View Post
Found a nice way to make this a one man job. Use a hack saw to cut a notch into a nut of the same size as the one on your bolt. From below put this nut onto the bolt and clamp it with vise grips. this will keep the bolt from spinning. you can then hold the bolt still, and twist the holding nut with another wrench. works nicely.

I believe what Rheaton is saying is that he cut all the way through one side of a nut. (Rather than a notch). He then threaded the nut onto the bottom of the bolt below the actual nut he was tightening and then grabbed it with the vice grips. The nut having been cut through on one side became a clamp on the threads of the bolt holding it firmly.
Damn good idea in theory.

Steve
06-09-2008 06:44 PM
sailingdog If the fastener holes go through cored laminate and you're not sure about whether the holes were properly potted or not... you should definitely pot them before proceeding. If you're going to bother with all this work, you might as well do it right.
06-09-2008 12:07 PM
Freesail99 I used silkaflex 291, because it does have a good adhesive power and is flexable.

If you drill new holes you may want to pot them with epoxy, you may also want to do that even if you don't drill new holes.
06-09-2008 12:01 PM
lbdavis I rebedded a stanchion and my pushpit (along with some other assorted deck hardware) this spring and I used 3M101 - a polysulfide sealant. It has relatively low adhesive power, but will stay soft and watertight for a long time. It is also easy to remove WHEN you have to remove it.

And as Halekai will be quick to point out, you don't need a ton of adhesive power on such a strong mechanical attachment.

I would second other's comments here and over-drill-and-fill all holes, then countersink the new ones.
06-09-2008 11:56 AM
Joel73 Thanks for resurrecting this thread... i will be re-bedding at some point this fall. What i'm unclear about is what kind of sealant to use... not 5200, that much i know.
This thread has more than 10 replies. Click here to review the whole thread.

 
Posting Rules
You may post new threads
You may post replies
You may post attachments
You may edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On


All times are GMT -4. The time now is 02:29 AM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) Marine.com LLC 2000-2012

The SailNet.com store is owned and operated by a company independent of the SailNet.com forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.