SailNet Community - Reply to Topic
Thread: Auto pilot problems Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.

User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

  Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below

  Topic Review (Newest First)
12-22-2008 07:15 AM
Originally Posted by Joesaila View Post
I didn't realize the autohelm drew significant amps. So now I know...
Yeah - been there, got that T-shirt. Sadly, some idiot had left both batteries connected, so we ended up with no power at all. I won't make that mistake again.

Of course, the extent to which the battery drains depends on how hard the autohelm is working, so sea conditions, point of sail etc will affect the time taken to reduce the battery to an unusable level.....

12-21-2008 10:53 AM
Low Batt?

Mine did the same thing you described last summer and it ended up being a low battery. I had it connected to just one battery and sailed a lot without running the engine on a week long trip. Initially I suspected metal near the fluxgate compass but after moving anything suspicious my buddy suggested low battery. He was right! Duh... I didn't realize the autohelm drew significant amps. So now I know...
12-21-2008 10:43 AM
robbert I have a Autohelm 6000 Autopilot, which Control panel is beeping all the time and no longer reacts to button commands. Most likely water has been inside the Control box as there are no seals at the screws!
Has anybody a Display/Controlbox for sale?
I am single handling and this device is very helpfull in doing that. Robbert.
06-16-2008 06:48 AM
SYMandalay I am guessing yours is similar to my 6000 series. Pull the plug out of the back of the display and give the connections a dose of electronics cleaner (Radio Shack). If I remember right, the power wire clamps on the computer work the same way as the others but require a lot of pressure in order to get them open.

It sounds like your display is either not getting power or has died.

06-16-2008 02:11 AM
negrini Looks like you have bad contact connections, what could produce low power to feed the system. Check your entire connection for loose wires, bad connection, corrosion, etc ... It might be possible Ray web still have the installation manual for the 300. But Chris, the way you describe it, you're short of electronics proficiency, so looking by yourself, you might miss something that trained eyes would do. Contact a tech guy ... it might be a simple fix.
06-15-2008 09:09 PM
Auto pilot problems

I'm having problems with my auto pilot. It is a Auto Helm ST70 type 300.

It started crapping out a couple of weeks ago. Sometimes when I turn it on, the control panel for the autopilot is blank. Sometimes it is blank and there is a alarm squealing. Sometimes it works. Sometimes I can turn it off and back on again and it starts working again. Or at least it used to. Now I think it is just in the blank display with squealing alarm mode. All my other instruments seem to be ok.

Has anybody ever seen this sort of problem before?

My first thought it that is a loose connection somewhere. Maybe low power.

It tried to reseat the power coming into the main computer. But I'm a little confused how the wire clamps are supposed to work. There are big ones and little ones. The little ones are obvious. There is a tab above the wire hole. You depress the tab and the wire is released. Let go of the tab and the wire is clamped. There are a couple of big clamps for power input and out to the drive motor. These don't have a tab. I'm not sure how to release the wire. I tried a couple of things but I didn't want to push to hard and break something.

Does anybody have any tips?

Chris King
Alden 44
Berkeley Ca.

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

For the best viewing experience please update your browser to Google Chrome