SailNet Community - Reply to Topic
Thread: Xantrex Truecharge 40+ only charging at 20 amps? Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.

User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

  Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below

  Topic Review (Newest First)
07-11-2008 12:52 PM
camaraderie can disconnect the two other reds t the charger and just try charging ONE well discharged deep cycle bank and see what happens. I am thinking that the voltage from the starting battery is tricking the charger into absorbtion mode rather than bulk if indeed all you are getting is 20amps.
07-11-2008 10:58 AM
PilotAlso Thanks,

I don't care for the multiple battery banks either but due to the physical locations of the banks (opposite sides of the boat) I decided to separate them.

Yes, I can isolate, or combine, each bank.

Looks like its time to buy a real battery monitor system to see actual charge current.

FWIW: The last time I charged the batteries, I tried running one circuit only and hooking it directly to a very low battery (the refer battery after using it all day). I hooked to it with #6 wire positive (6 feet) and #8 neg (8 feet) directly. I had the temp sensor on the battery in 80 deg heat.

I still saw only 20 amps charge indicated on the charger. (wish I had a real ammeter)

I think I'll be calling Xantrex support.
07-11-2008 02:12 AM
camaraderie From the Manual:
"Truecharge+ has three separate DC positive terminals to allow charging
of three separate batteries (or battery banks). The total current into the
batteries is a maximum of 40 amperes
, which is divided amongst the batteries according to their state of discharge.
Note: The three outputs are not independently voltage regulated so it
is important to avoid systems with mixed types of batteries."

The Remote Display Panel allows you to monitor battery charger activity
away from the charger whenever Truecharge+ is operating. The panel
displays the total charging current and the voltages of the two batteries or battery banks connected to the two positive terminals closest
to the
negative terminal."
Note the wiring issue in bold which depending on your hook up may be distorting charging readings particularly if your start battery is wired in position #1 or #2 immediately to the right of the negative terminal.

If you can switch your batteris OUT of the charging one bank down low till you get a 12.2V reading without any load on it. THEN just charge that battery bank and you should see 40amps or there is a problem. I am not a fan of 2 house banks but if you can isolate each AND the starter battery for charging, you may see better results.

The other thing I would note is that if you are simply using the panel display to read amperage, you are NOT getting the whole could be getting 39amps and never seeing anything but the 20 amp light come on. ONLY when you hit 40 amps will that lamp come on. You need to measure REAL amperage with an ammeter!
07-10-2008 11:51 PM
Xantrex Truecharge 40+ only charging at 20 amps?

I recently upgraded to this charger.

Our boat is on a mooring ball. We use a Honda 2000 to power the Xantrex.

We have two flooded batteries in one bank (powering radar, chartplotter, and refridge).

The other bank is a two flooded battery house bank.

The last is a simple start battery.

Even when the banks are run down pretty low, we only see a 20 AMP charge on the Xantrex and have never seen 40.

All 5 batteries are brand new (this year) 12 volt flooded deep cycle.

Is this NORMAL or expected? or EXPLAINABLE?


Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

For the best viewing experience please update your browser to Google Chrome