SailNet Community - Reply to Topic

   Search Sailnet:

 forums  store  


Quick Menu
Forums           
Articles          
Galleries        
Boat Reviews  
Classifieds     
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Charts
Clothing
Electrical
Electronics
Engine
Hatches and Portlights
Interior And Galley
Maintenance
Marine Electronics
Navigation
Other Items
Plumbing and Pumps
Rigging
Safety
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here






Go Back   SailNet Community > On Board > Gear & Maintenance > learning to work in fiberglass
 Not a Member? 


Thread: learning to work in fiberglass Reply to Thread
Title:
  

By choosing to post the reply below you agree to the rules you agreed to when joining Sailnet.
Click Here to view those rules.

Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Topic Review (Newest First)
08-15-2004 11:11 AM
Oatman
learning to work in fiberglass

I''m also looking for a fiberglass guide. I''ve been using the West System guides and Vaitses''(?)Fiberglass Boat Repair Manual. They were both very informative as far as handling the material, repairing gel coat,holes,and osmosis.
My problem is, after a brutal grounding of my Cal 25(pile driven on rocks by 4''surf till I kedged off),I pretty much must completely re-layup the bottom 12" of the keel. In addition the leading edge must be reformed from the ballast out just where it turns aft and, astern, the starboard section with the reverse curve tapering to the trailing edge must be rebuilt from the centerline out. The bottom 12" of the actual trailing edge must also be recreated.
I have searched for months but can find no support to explain any of it! I did Email West System, receiving early advice about laying up "straps", to insure ballast integrity. I just sent them another email detailing the extent of the damage, including a rough sketch. They seemed very enthusiastic in the first response and I hope they can supply a solution.
Yet, I have sent Emails requesting advice at several other sites and have heard nothing. Perhaps they can''t find a good book either (he he he).
11-24-2003 11:33 AM
geohan
learning to work in fiberglass

One of my favorite references is "The Boat Repair Manual" by George Buchanan, Arco Publishing, Inc. New York. For fiberglass construction, small and large holes, delamination, core repair, etc. are covered step by step begining on page 84.
Regards, George
11-24-2003 11:04 AM
sailingfool
learning to work in fiberglass

Try the free literature and Product Guides available from the Product Information section of the West System website http://www.westsystem.com/

West products are the way to go for amateur do-it-yourself work; good products, good information and very easy to use dispensing gear, small batches or big.
11-24-2003 07:01 AM
jbarros
learning to work in fiberglass

Hey all,

could anyone recomend a good book on the range of fiberglass repairs, from repairing small holes to reenforcing glass thats gone flexy, etc?

Thanks.

-- James

 
Posting Rules
You may post new threads
You may post replies
You may post attachments
You may edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On


All times are GMT -4. The time now is 06:01 AM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) Marine.com LLC 2000-2012

The SailNet.com store is owned and operated by a company independent of the SailNet.com forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.