SailNet Community - Reply to Topic

   Search Sailnet:

 forums  store  


Quick Menu
Forums           
Articles          
Galleries        
Boat Reviews  
Classifieds     
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Charts
Clothing
Electrical
Electronics
Engine
Hatches and Portlights
Interior And Galley
Maintenance
Marine Electronics
Navigation
Other Items
Plumbing and Pumps
Rigging
Safety
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here






Go Back   SailNet Community > On Board > Boat Review and Purchase Forum > Sailboat Design and Construction > Changing a V-Cleat to a C-Cleat?
 Not a Member? 


Thread: Changing a V-Cleat to a C-Cleat? Reply to Thread
Title:
  

By choosing to post the reply below you agree to the rules you agreed to when joining Sailnet.
Click Here to view those rules.

Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Topic Review (Newest First)
08-21-2008 11:14 AM
funjohnson The razor sounds like a good idea too.

I have access from below deck that will help make this a much easier process. I will also upgrade to bolts and washers to help support the cleat.
08-21-2008 09:48 AM
sailingdog If you're going to use Chuckles's Razor blade as putty knife trick, do yourself a big favor and round off the corners of the blade. It will go a long way to preventing the blade from digging in and gouging the gelcoat.
08-20-2008 08:28 PM
chucklesR A neat trick for patching the screw holes left behind - use a old fashioned razor as your putty knife, it is so smooth you can get away without sanding as the razor is smooth on it's edge.

Use either finger nail polish remover or acetone (the active ingredient to polish remover) and a q tip to wipe/scrub away the Marine tex that isn't part of the hole. I'd put tape around the hole to limit the clean up.
No one but you will know it's there.

But you'll always know

You will need to look to where the current clam cleat is fastened, is it simply screwed in, or is it mounted with bolts etc.. that might entail removing the liner from the cabin/getting under the cockpit coaming. If it's simply screwed in now you and you can get to the underside go ahead and upgrade to a bolt with a big finder washer to offer more support.
Assuming you normally take a few wraps around a winch and the cleat is simply to hold the line it might not take much to hold it, but bigger is always better.
08-20-2008 08:17 PM
capn_dave
Yep the DOG

and I are on the same page. Those are good cleats the the Dog picked out.

Here in windy and wet North Florida

Fair WInds

Cap'n Dave
08-20-2008 07:04 PM
funjohnson You guys are awesome! I'm about to order the cam cleats listed. This should be a great project for the holiday weekend.

Thanks again,

Matt
08-20-2008 05:59 PM
sailingdog I'm a big fan of these. LINK


08-20-2008 05:42 PM
zz4gta Just make sure they'll accept your size sheets.

http://www.defender.com/category.jsp?path=-1|118&id=295771
08-20-2008 05:34 PM
funjohnson Thanks for that info. Do you have any cam cleats you would recommend? Are there any bad ones?

That explains why I was not able to find much by searching "v-cleat"
08-20-2008 05:29 PM
sailingdog Unless you're using a large expanse of Marine-tex, you're not going to significantly weaken the deck by using it. The holes can be safely and easily filled using MT...

Just FYI—The "v-cleats" are actually called clam cleats.



The ones I have pictured are ones with an integrated fairlead.


Would also recommend you read the post in my signature... to get the most out of your time here on sailnet. Welcome to the asylum.
08-20-2008 05:16 PM
funjohnson Would the Marine Tex be as strong as the original fiberglass? I do not want to weaken the deck.
This thread has more than 10 replies. Click here to review the whole thread.

 
Posting Rules
You may post new threads
You may post replies
You may post attachments
You may edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On


All times are GMT -4. The time now is 06:11 PM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) Marine.com LLC 2000-2012

The SailNet.com store is owned and operated by a company independent of the SailNet.com forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.