|Topic Review (Newest First)|
|03-20-2009 09:48 PM|
and more mast
Adding the antlers,
masthead nav/anchor w/antenna and windex. masthead light is carved out and modified to have a 1/4" clear (now yellowed) plexiglass top w/VHF antenna and windex. the plexi is to let out some light to illuminate wndex.
behind that I built a wing to lower everything ese below lights.is the rotovecta wind cups for the Raytheon St-40 and the rabbits foot of the industry a negative ion lightning protection device. May be a rabbits foot but it's MY rabbits foot.
This is hanging with max moment load, no sweat, but there isn't "gusty" conditions that started this mod.
|03-16-2009 07:21 PM|
That is the foil for the roller furling, kind of relaxed on the forestay.
I've always had the admiral assist with the stepping. Gustav made me reconsider my ways during "gusty" conditions. 12 years of doin' it one way and I'm changing it. I really hope to step the stick more often since I want to drag her around behind my dog.
linkey... Telstar Mast Raising - A Patented System
|03-16-2009 07:13 PM|
|kwaltersmi||I kept my mast stepping system very simple. I used a 10' 2x6 gin pole and an extension ladder for a mast crutch at the stern. I then simply used a line run from the end of the gin pole through a snap block on the bow and back to the jib sheet winch and hoisted her up. It's definately a two person job (one on the winch, one steadying the mast) and easier with 3, but it was actually much less difficult than I imagined.|
|03-16-2009 07:07 PM|
I meant the mast slot Aframe to be in addition to the stanchion Aframe. I'll look up the Telstar info for ideas.
Do you have a PVC conduit going up the outside of your mast? For wiring I presume. Nice idea, easy access. I hope you added another 1000# of ballast for all that stuff up there :-)
|03-16-2009 06:51 PM|
I think you'll find all kind of "fun facts" I've dealt with the assymetrical issue.
I have seen the catalina 22 and I don't want that type.
Look up the Telstar trimaran, several A-frames and yokes make a smooth stepping, but I'm just not that cool.
I already stress over that damn sailtrack, mine gets more lubing than I do! I didn't see wedging beneath th' hand holds as positive as stanchion base, I feel I have good control and allows for the torque. I used my 1/4" Spinoa halyard since it's hung outboard on a bale, I need to clear a midmast radar reflector. I'm gonna hang the antlers on her when it stops raining. This is a pix of the masthead, bale, side block is for the topping lift. I end up with 4 line aloft, there is also a st.stl. strap beneath the masthead crane, I use a Hood 705 and this strap/guide prevents "issues" with the roller and doesn't interfere at all w/Main halyard.
|03-16-2009 05:32 PM|
I also found out that my stanchion plates are not placed the same on each side. Neither are my pad eyes for the shrouds. I think they said "That looks good" when they installed them. it also means my rigging is different in length from Port to Starboard. Not by a lot, but enough to almost have no more adjustment on my starboard side turnbuckle to make sure my mast is plumb.
Here is that U Tube cut of the mast raising rig on a Catalina 22. He uses chocks in the handholds and a gooseneck fitting in the mast groove that rides up and down to accommodate the difference in the hinge plane. Good idea. I'm going to try it.
YouTube - Mast Stepping Catalina 22 (1st Take)
|03-16-2009 04:08 PM|
|jumaggafanny||Mine are 10 ft, I intend to modify the Stbd one by cutting 3" off to center it. I only raised the mast once and set it back down. When it quits raining I'll try it again with the mast antlers.|
|03-15-2009 09:03 PM|
Did you use 10' EMT lengths. I measured the distance form the stansions to the pulit and it looks like 10' will be just right.
I'm making one also to replace my Ginpole. Although the ginpole is longer and gives more leverage, the A frame is more stable.
I also got an idea from Utube to make anothe A frame from the deck hand rails to the mast slot to support the mast laterally. I'll see if i can find the clip and post it. It looks simple and secure.
|03-15-2009 06:10 PM|
Mast stepping "rig"
I ended up with a few false starts making this rig work for me. I wanted something that breaks down since I have to carry it to my launch site a state line away. I am using 1" Electric conduit (emt) and used 1" OD 0.065 wall st. stl. pipe for the fittings, I used an cut ring of 2" pipe at the apex of the A-frame. This would not be suitable for Helms that do not have lifelines and the attendant stanchions. I was pretty pleased with myself for using the stanchion base, I couldn't lose the stanchion since the life line keeps it near and I know it's mounted and backed well. I still use the 4:1 from the bow to the frame. I anitcipated the need to shorten each side of the frame but that wasn't required. I am fortunate to have an inner stay to attach since mainstay involves installing the roller furling.
|01-20-2009 09:41 AM|
Here the pics. need to use the little mountain symbol
|This thread has more than 10 replies. Click here to review the whole thread.|