|Topic Review (Newest First)|
|11-09-2008 06:36 AM|
|sailingdog||Good enuf... keep us posted fuzzy.|
|11-09-2008 01:50 AM|
Hey look, thanks for all that. I've been a little bit out of the loop this week and have only just noticed the updates. Much appreciated.
Knut..thanks for the pics.
SD....I think that is what we have already. The problem is the positioning I think. Must play.
Faster...I've used the spinlock thing on another boat and I found it a pain in tha bum but maybe that was simply lack of familiarity.
|10-27-2008 04:42 PM|
I promised you some pictures, here they are.
This picture is taken through the sprayhood (dodger?)
Here is a picture of the lead at the turnbuckle.
The turning blocks at boom neck and chainplate are fastened with dyneema loops. A piece of chock cord is used to lift the lower blocks when there is no sheet load.
Main sheet winch and cheek block
Testing out lead for new configuration, this change will probably also involve switching position of the winches. With this setup both sheets (main & jib) can be handled from the wheel.
I know that a lot of boats with this configuration has 1:2 purchase on the main sheet = faster sheeting if winches give enough purchase. If you have a large crew both winches can be used simultaneously to sheet the main (if you use other winches for the jib)
|10-26-2008 02:28 PM|
Have you looked at something like this:
The Nash Trigger cleat has a unique mechanism that allows you to release highly loaded lines with complete control. Pulling the sheet down on the trigger trips the pawls and frees the sheet. The trigger serves as a snubbing surface to control release.
In light air, or once the trigger releases the load, the cleat operates like a normal cam cleat. The Trigger cleat is constructed of rugged stainless steel. It is very reliable in heavy air. Trigger cleats are ideal on highly loaded systems like mainsheets, vangs, and even for some halyards. They have developed a cult-like following in some classes where the crew loves the ability to spill the mainsail reliably during close-quarters maneuvering.
Sailnet can probably get them, but I didn't find them on the Sailnet store. Mauri Pro Sailing does have them.
|10-26-2008 02:12 PM|
W - have a look at these:
Welcome to the Spinlock Website | www.spinlock.co.uk
Friends swear by their ability to easily release under load.. perhaps you can retrofit one of these on your mainsheet block.. sorry about the corrupted link...
|10-25-2008 08:25 PM|
Originally Posted by Valiente View Post
Ironically, having made the decision to look US the OZ dollar promptly collapsed and the two boats we were looking at shot up by many tens of thousands due to the exchange rate variation. Sadly, a largish chunk of our retirment funds are invested in stocks and shares so we are also not quite as well off as we were a few months ago. Thankfully we transferred a goodly lump into cash earlier this year so its not all doom and gloom.
The Wombette and I then decided that we would take a breather from the boat buying market for a year or two or until the Oz dollar recovers.
The current Womboat is 34'. Working on a 2009 buggering off point we have a boat that is sound, a relatively good performer and just, but only just, big enough for us.
The alterations and updates we are going to do are relatively minor and in the main making her easier to sail, single or double handed, and more self sufficient in power system and food storage capacity.
ZZ - Purchase is not really the problem and if I needed more I could simply go to 8:1 instead of 6:1. Only real problem with 8:1 is the amount of line flopping about in the cockpit . I don't have any great problem hauling the main with 6:1. The problem I do have is releasing the damn thing. (edited )
To be honest, it is more a problem of traveller position than anything else. The Womboats traveller runs across the cockpit just forward of the wheel. For the helmsman to release the main sheet you are required to lean over the pedestal and reach down to the block. It's simply not a good way of doing it and I'm looking to figure how best to overcome the problem.
I'll try and take a couple of shots of what is there now and post later today.
edited - cocked up the ratios. Thanks to HArken website, this is effectively what we have now...
|10-24-2008 12:41 PM|
|zz4gta||Why not add a cascade or 2 speed mainsheet system. It's gotta be cheaper than adding 2 winches and clutches.|
|10-24-2008 12:23 PM|
|Valiente||That 40 footer is off the table, then? You're sticking with the steel beastie for now? (I recall it's 34-35 feet or something, which is about as compact as you want in steel).|
|10-23-2008 10:26 PM|
Originally Posted by Faster View Post
Too true re the lead angle from the clutch to the winch. This is a very recent concept to me so I'm still very much in planning stage but remember that the Womboat is steel. Fabricating something on which to mount the clutch would not be difficult and I have easy access under that part of the deck or coaming for attachments.
I need to add at least two new winches to the old girl as it is so if I have a problem it will be space for winches.
Provided weather holds I'll be on board tomorrow. Will have a good look then.
Knut - It may well be that I get this done before your winter is over. I'll keep you informed of my progress.
ps - ref the German or Admiral's Cup system.....word is that it was a German boat called Pinta. Not confirmed.
|10-23-2008 10:06 PM|
But it is also necessary to be able to adjust the main sheet rapidly in some cases.
In my current setup I have a cheek block to lead the sheet to the winch.
I have not had any incidents with fouled sheet with this configuration.
The problem with kinks will always be there when a rope has to pass through a block, clutch or something else, the key here is to keep the rope clear without kinks.
The sheet should never be clutched and tailed on the same side simultaneously, but I dont think using clutches only will be so bad.
I'm going to use Lewmar clutches - they can be used as a brake when releasing the rope, so you can controll the rope release without using the winch.
Sailing season is over for me, boat on the hard and mast down for some modifications - so i will not be able to report on the practical use before next summer. But I have seen this setup on several boats and is quite confident that it will work.
|This thread has more than 10 replies. Click here to review the whole thread.|