SailNet Community - Reply to Topic

   Search Sailnet:

 forums  store  


Quick Menu
Forums           
Articles          
Galleries        
Boat Reviews  
Classifieds     
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Charts
Clothing
Electrical
Electronics
Engine
Hatches and Portlights
Interior And Galley
Maintenance
Marine Electronics
Navigation
Other Items
Plumbing and Pumps
Rigging
Safety
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here






Go Back   SailNet Community > On Board > Gear & Maintenance > MD7A Volvo Penta Timing Gear
 Not a Member? 


Thread: MD7A Volvo Penta Timing Gear Reply to Thread
Title:
  

By choosing to post the reply below you agree to the rules you agreed to when joining Sailnet.
Click Here to view those rules.

Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Topic Review (Newest First)
10-27-2008 03:23 PM
Rockter Valve timing is also critical though.
10-27-2008 09:34 AM
erps
Quote:
The timing of a tooth or two either way on the valve train should not effect starting... I'd set it to factory spec and leave it.
Unless the injection pump is gear driven off the cam shaft. Injector timing is critical.
10-27-2008 02:40 AM
Rockter Guys, depending on the size of the gear wheel, two teeth off could be quite an error. I take it that this is the camshaft gear?
10-26-2008 04:46 PM
harbin2 I just bought an Islander 30 two months ago. I has an MD7A diesel also. I thought it was hard starting too. I talked to the Volvo rep at the Annapolis boat show earlier this month. He said to start it at half throttle and back off once it fires up. I tried that and it starts in about 10 seconds instead of 30 to 40.
Ron
10-26-2008 04:31 PM
dem45133
Comments on Timing Question vs starting ???

OK... if I understand correctly just rebuilt it but takes a few turns to start... couple teeth off really shouldn't have anything to do with it to my way of thinking. I just got a MD7A that was submerged for a week, and then sat for a month with the crank case full of water (good actually, no O2 available to start rust) and am in the process of tearing down as it sank while it was running. Might have bent a rod when it hydro'd. So I'm opening it up to totally clean up everything and inspect. Point is I've been inside alot of engines and have been for almost 40 years.... the observation you made makes some sense on a brand new engine. Remember, on a new or fresh rebuilt, the rings and cylinders are not broke in yet and as such can act like it has bad compression. Low compression on a diesel can start harder until the oil pressure created while cranking has lubed the cylinders enough to fill the micro groves left from honing. Especially if its cranking slow by being stiff yet. Once the rings are seated and the micro groves worn and sealed the compression will be much higher. This post is a little old so maybe its remedied itself by now.

The timing of a tooth or two either way on the valve train should not effect starting... I'd set it to factory spec and leave it.


Dave
07-21-2008 09:10 AM
shebobah
MD7A Volvo Penta Timing Gear

I have a MD7A Volvo Penta in my 1978 Newport Mark II. We just got finish rebuilding the whole engine and it takes quiet a few turns before it fires up. Some one who works on Volvo Pentas a lot said "he thinks" this motors timing gear is supposed to be a couple teeth off. When we took it apart we noticed that it was a couple teeth off and thought that the last person who put it together made a mistake. This is before the person told us "he thinks" .So, we put it together the way the manual said to line up the teeth, which is number to number.

I have called numerous people, sent volvo an email (with no reply) and called some parts houses. No one has heard of this. At this point it is just a rumor. Before we go back in to the engine it would be good to know if this is true or not.

Does any one have any information on this?

Mike

 
Posting Rules
You may post new threads
You may post replies
You may post attachments
You may edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On


All times are GMT -4. The time now is 12:09 PM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) Marine.com LLC 2000-2012

The SailNet.com store is owned and operated by a company independent of the SailNet.com forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.