|Topic Review (Newest First)|
|12-30-2008 01:34 AM|
If your lines stretch, you have also potentially lost power to the sails, and speed, hence why one would want to use a less stretchy line for sheets, along with halyards. Not to mention the sail cloth itself, hence why racers use carbon and kevlar with mylar too in sails vs dacron these days. Many cruisers are using this higher tech, less stretchy material, so they do not have to spend a lot of time readjusting things for stretch, along with getting more out of the boat for a given weather conditon too.
Some of this stretch could cause more heeling without adjusting thing constantly too, as you will not have the sails at the proper setting for any length of time.
Many reasons to go with less stretchy lines and cloths. It comes down to how much you want to spend, how much improvement you want etc. Plus's and minus's to both!
|12-29-2008 02:25 PM|
Why bother adjusting your sheets if all they're going to do is stretch anyway?
Only thing that should stetch is dock lines, and anchor rode. Nothing else. Smaller high tech lines will kink/hockle less and won't absorb as much water as the fuzzy daysailing lines. They are hard on the hands, some require to be scuffed up a bit to grip a winch, but to me, they were worth it.
|12-28-2008 02:38 AM|
I have a stupid question. Why is everyone using low-stretch line for Jib sheets? When I needed new ones, I went with Regatta Braid. If I want the sail sheeted in tighter, I simply take in more line. I certainly see the advantage to having low stretch halyards as you are only adjusting them (if at all) a couple of times during a day-sail. But the sheets are constantly being adjusted so what is gained by using a low stretch line? One could argue that it would be preferable to use a stretchy line to spill gusts ....
|12-27-2008 07:29 AM|
I changed from Sta-Set to Regatta Braid. Sta-Set was kinking on me and would get caught. It was a real PITA. The Regatta braid has been great. I can't believe how fast it comes off the winch when tacking, even in light air. I've heard that Andersen self tailing winches don't like it very much, so if you have self tailing winches you might check for compatibility.
I also use one long line for my jib sheets. I had 2 lines with the Sta-Set and found that the bowline would hang on the shrouds in light air. The small knot right at the clew with a single line never gets hung up.
|12-27-2008 04:01 AM|
I club race, but do like to get as close to every ounce speed out of my rig I can, so I went with the XLSx before I really started to race. More because there were more choices of colors to the spouses preference! Maybe take her in to choose the colors!
I use one long sheet tied off in the middle. I did have hanks until mic Oct when the new carbon 155 came in. Then I went with a Carbo foil.
I have thought about the idea of cutting my sheets in half, and tieing them on seperatly. But reality is, I have a sheet for the 155, and the 110, along with a sheet for the AS, and a Guy sheet if I want to tie a pole to the tack, which can be helpfull in light wind conditions.
Yeah, it is a bunch of money in line/rope, but a lot easier to figure out what goes with what, all color coded etc.
|12-26-2008 08:58 PM|
The 'Grammar Police" agree with SemiJim. There are jib sheets (as there is one to the port and another on the starboard side - also known as a windward sheet and a lazy sheet depending on point of sail) but there is usually only 1 main sheet as the same sheet works for all points of sail.
Interestingly, new sailors often make the obvious association that a 'sheet' should mean a piece of fabric like the material that covers a bed or a sail but are usually disabused of this notion by some know-it-all skipper who will usually be yelling.
Jib sheets require a lot of handling which is why many people prefer them in larger diameters which are easier on the hands. Sailing gloves or bike riding gloves can help a crew minimize blisters and chafing of the hands from working the sheets.
A spinnaker sail has a sheet as well as a guy which is way confusing and beyond the OP.
|12-26-2008 06:48 PM|
Originally Posted by SEMIJim View Post
|12-26-2008 06:05 PM|
Originally Posted by mwrohde2 View Post
|12-26-2008 05:53 PM|
I'd like to go with Sta Set X for the main halyard. The Admiral is balking at the additional expense. Local WM guy is telling us that for just club racing, regular old Sta Set is sufficient. (He's probably right.)
|12-26-2008 03:02 PM|
Originally Posted by SEMIJim View Post
|This thread has more than 10 replies. Click here to review the whole thread.|