SailNet Community - Reply to Topic
Thread: Fuel Return Ratio Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.

User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

  Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below

  Topic Review (Newest First)
07-22-2004 01:22 AM
Fuel Return Ratio

The total engine fuel flow, on a 3GM30 ( 27hp ) is not much greater than the engine fuel consumption as the return flow is low.
On a 6CX-ETE ( 420hp ) the total flow is 846 litres per hour at full power. The return flow is 756 litres per hour give or take a bit.

So, you may wish to take my previous advice with a grain of salt, and do what you can to confirm the approximation.

07-12-2004 06:56 AM
Fuel Return Ratio


Thanks for your very detailed response. This precisely what I was hoping for.

BoatBum, Sorry for the two posts. I didn''t realize this would confuse anyone (though I''d just recommend reading "one thread" if two are baffling).
07-11-2004 02:47 PM
Fuel Return Ratio

You know, this post is in two places, thus the disfunctional understanding of what the deal is. Check out General Discussions. It PMO when things are in two places, the thread can''t be followed.
07-11-2004 01:51 PM
Fuel Return Ratio

If your return is rubber tubing, it would be easy to disconnect it and measure the amount returned in a given time. If copper, there would be a flex connection near the engine that could be undone.
07-11-2004 04:29 AM
Fuel Return Ratio

That is, 2 gallons are returned for each gallon burned (3 gallons total supply flow)
NOTE: I have read where others state the ratio at about 1:1 - so caveat emptor applies!

A diesel engine’s TOTAL FUEL FLOW RATE is often cited as APPROXIMATELY: horsepower x 18% = gph
thus a 30-hp diesel would have a theoretical total flow rate of 5.4 gph. (30 x 0.18 = 5.4)

Diesel engines consume about 1 gallon per hour for every 18 hp used. You can estimate the number of gallons consumed per hour by multiplying horsepower used by 0.055.
thus a 30-hp diesel would have a conservative theoretical consumption rate of 1.65 gph (30 - 18 or 30 x 0.055 = 1.65)
NOTE: This is an obvious approximation, as diesel''s have widely varying operating curves.

The Return rate would be Total Flow less Consumption = Return
thus (from above)
5.4 Flow - 1.65 Consumption = 3.27 gph Return
3.27 return divided by 1.65 consumption = 1.98:1 Return / Flow Ratio
hence the Rule of Thumb:
Return is Twice Consumption (henceTotal Flow is 3 Times Consumption)
5.4 Flow divided by 1.65 Consumption = 3.27:1 Flow/Consumption Ratio


07-10-2004 04:14 PM
Fuel Return Ratio

Gord and Paul,

While I appreciate your replies, neither of you answered my question. Yes I''m aware that it is not a premium system configuration (as you said, "for obvious reasons"). So what I really need is not an "ABYC standards recommendation." I would love a "ball park figure" or even guestimated range of "diesel returned" during normal function. Once again, thanks for reading my inquiry and posting a response, but what I need is a "fuel return ratio." Even a guess would be useful. Thanks,
07-10-2004 11:01 AM
Fuel Return Ratio

Gord is coreect. This is very bad! On my boat when I switch tanks I also switch the return line with a Y valve. On one side I mark red and the other green. The valve sits next to the tank selector.

It''s not that hard to add a valve to redirect the return line to the proper tank it came from.
07-10-2004 01:22 AM
Fuel Return Ratio

For obvious reasons, this is a poor practice (not returning fuel to the tank that supplied it, and unacceptable under ABYC "Standards & Recommended Practices..."
07-09-2004 09:27 AM
Fuel Return Ratio

Here''s a highly variable question: How much diesel gets returned to the fuel tank in the process of running your engine, verses what gets burned.

For example, if I run my engine for 10 hours at a consumption rate of 1.15 gallons per hour, that''s 11.5 gallons of fuel used. My question is, how much got sent from the tank to the engine in the process and then returned to the tank? I''ve heard people say that as much gets sent back as is used (ie. the pump sent 22 gallons to the engine and 11 got returned to the fuel tank).

Does anyone have a definitive notion of what the return ratio is??? I''ve recently had a hard time calculating "what''s in my tanks" because regardless of which tank I''m using, the engine only returns fuel to the primary tank. HELP!!!

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

For the best viewing experience please update your browser to Google Chrome