SailNet Community - Reply to Topic

   Search Sailnet:

 forums  store  


Quick Menu
Forums           
Articles          
Galleries        
Boat Reviews  
Classifieds     
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Charts
Clothing
Electrical
Electronics
Engine
Hatches and Portlights
Interior And Galley
Maintenance
Marine Electronics
Navigation
Other Items
Plumbing and Pumps
Rigging
Safety
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here






Go Back   SailNet Community > Boat Builders Row > Hunter > H460 - 2000 - Fresh H2O pressure
 Not a Member? 


Thread: H460 - 2000 - Fresh H2O pressure Reply to Thread
Title:
  

By choosing to post the reply below you agree to the rules you agreed to when joining Sailnet.
Click Here to view those rules.

Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Topic Review (Newest First)
01-28-2009 02:28 PM
velero Are you shure that is the fresh water system? Do you leave your sump pumps breaker on all the time? On my H46 I have 2 sump pumps that collects water from the drains of both showers and the A/C drains (which I conected myself to the sumps). The sumps drive me crazy at night because the switch is very sensitive and runs like you describe every few minutes. The forward one is the one that bothers me the most but I think both of them do the same thing. The one in the middle of the boat is near the fresh water pump.

Good luck,

Velero
01-28-2009 01:07 PM
camaraderie I believe you are talking about accumulator tanks which reduce pressure cycles and smooth water flow. The tank itself may be an issue...make sure the pressure valve is closed. If there is constant cycling...there is either a small air leak in the system or a faulty pressure valve on the pump. The latter is the place to start as it is easier to diagnose and fix or eliminate as an issue.

If there is a leak...the place it will likely be is at a joint/hose clamp. Tighten all of those and look for obvious issues like water drips as a first step. If that does not do the trick the only alternative is to eliminate the section of hose where the loss is occurring by working forward from the pump outlet to the individual joints and removing the hose at those joints and plugging the hose up tight. If the pressure holds...then move on to the next joint etc. until you find what section is at issue and then simply inspect and/or replace it.
01-28-2009 11:56 AM
Bene505 We have a little blue tank on the pressure side of our f/w system, that does the same thing and works the same way. You can buy these instead of building them. I'll get a picture if you want one (and can wait until I'm on our boat next).


Quote:
Originally Posted by captdave57 View Post
The pressure sys. is designed with the check valve at the pump. the filter {should be}, on the inlet side of the pump between the tank and the pump. Advent #1, I put together a 4" x 24" clear plastic pipe with caps on both ends and a 1/2" inlet fitting near one end and a 1/2" fitting mid-way along the same plane on the body of the pipe. now the water under pressure comes in the chamber mid way up the pipe and fills the chamber with water and the air is compressed to the power of the pump. The other fitting is connected to the service line for the water system ahead of the "T" for the hot and cold seperation.
This is a way to increase the amount to water that can be used, before the pump in needed to re-pressurize the system and gives a much greater flow volume.
Now as far as the check valve on the pump, you may need to disconect the line in and out and look for some contamination in the check valve spring and ball orafice. I have done this on our 86 HUNTER 31.4, it work well. and you may have a small leek at some connection or Ihave also seen a small line puncture with a screw that was install to hold something else that caused a small leek. I hope this may help.
S/V "Faithful Girl" 32' 1986
01-28-2009 11:54 AM
Bene505 I had a leaky faucet in both the kitchen and crew quarters (same model faucet was used). I took them apart and cleaned the gaskets.

In this case I could 1) see the water trickling down the side of the faucets, 2) hear the pimp cycling on all the time, 3) see the water in the bilge as a result, and 4) may have noticed water loss form the tanks too.

Are #3 and #4 happening with your boat?
01-28-2009 11:36 AM
captdave57 The pressure sys. is designed with the check valve at the pump. the filter {should be}, on the inlet side of the pump between the tank and the pump. Advent #1, I put together a 4" x 24" clear plastic pipe with caps on both ends and a 1/2" inlet fitting near one end and a 1/2" fitting mid-way along the same plane on the body of the pipe. now the water under pressure comes in the chamber mid way up the pipe and fills the chamber with water and the air is compressed to the power of the pump. The other fitting is connected to the service line for the water system ahead of the "T" for the hot and cold seperation.
This is a way to increase the amount to water that can be used, before the pump in needed to re-pressurize the system and gives a much greater flow volume.
Now as far as the check valve on the pump, you may need to disconect the line in and out and look for some contamination in the check valve spring and ball orafice. I have done this on our 86 HUNTER 31.4, it work well. and you may have a small leek at some connection or Ihave also seen a small line puncture with a screw that was install to hold something else that caused a small leek. I hope this may help.
S/V "Faithful Girl" 32' 1986
07-23-2008 12:13 AM
labatt We also had the same problem. We had just done some work on the system and there was a slight drip from one of the hoses, causing very very gradual depressurization and making the pump run every few minutes. We tightened the hose clamp and life was good.
07-22-2008 01:41 PM
clubara Do any work in the vicinity of the water lines recently?

Ran into the same thing a couple of years ago on my 466. Ended up being a loose connector. We had some work done under the settee that had jostled the cold water line. Simply pressing the connectors back together got rid of the leak. I carry extra connectors and hose now in case one of these were to leak more catastrophically.

allan

s/v Follow You Follow Me
07-12-2008 09:28 PM
trantor12020 Are you lossing water ? If not, check the water pump 1st. Maybe the check valves or flapper is passing, hence depressurising back to the tank.
07-07-2008 07:41 PM
ftt944
H460 - 2000 - Fresh H2O pressure

Have Done the Deed and now have a number of questions about systems that need 'fixin'.

Most vexing is constant re-cyclying of H2O pressure pump, approximately 1 minute between cycles, because the lines are not holding pressure. Before we send a horde of plumbers' children to college, any suggestions out there about how to trace site of pressure loss in the H2O system?

 
Posting Rules
You may post new threads
You may post replies
You may post attachments
You may edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On


All times are GMT -4. The time now is 07:06 PM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) Marine.com LLC 2000-2012

The SailNet.com store is owned and operated by a company independent of the SailNet.com forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.