SailNet Community - Reply to Topic
Thread: Use of Teflon Tape on fuel fittings Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.

User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

  Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below

  Topic Review (Newest First)
09-23-2004 06:50 PM
Use of Teflon Tape on fuel fittings

Silmaril, I truly appreciate your response and the research you have done. In looking for additional information I went to a local marine dealer/service department in our community and asked him what he recommened. The manager told me to use Locktite Blue. He regularily uses Locktite Blue on ALL fuel fittings he works on. He comments he has NEVER had a fuel fitting leak and that they are relatively easy to take apart as opposed to the RED Locktite which requires about 550 degrees to remove. I bought some Locktite Blue at our local hardware store and used it to put my fittings together. In doing so, I had to reposition two fittings and found they came apart with some effort but they did come apart. At this juncture I have not experienced any leakage. Many thanks again for your input. Regards, Peter
09-04-2004 12:47 PM
Use of Teflon Tape on fuel fittings

I went to some plumber friends first. They recommended the Rectorseal product as being very good. Being plumbers, they were the ones to say "Go with the teflon" go figure, hey they''re plumbers...

After reading the post regarding the teflon compound breaking down, I called the manufacturer. Getting in touch with their technical support group was easy, describing the conditions, ie: bronze threads, diesel, etc. they recommended their "No. 5" product, citing it''s excellent proberties with bronze threads and diesel.

09-02-2004 06:33 PM
Use of Teflon Tape on fuel fittings

Silmaril, thanks for your input. Can you tell me and the forum what research you have done and where you got the information? I would like to find out what you found. Where does one get the product Rectorseal No. 5? What is Rectorseal No. 5 and what makes it so good? Thanks again for your input. Peter
08-27-2004 11:01 AM
Use of Teflon Tape on fuel fittings

OK, so I have done some more research on the subject. The Product I used, Retorseal T plus 2 is not a good way to go. <sigh>

The diesel rated product for long term exposure is Rectorseal No. 5. Same process for application, it is pressure rated to 350 psi of diesel with no leakdown after 720 hours.

As mentioned by others, the manufacturer sayes the Teflon products will have their carrier desolve over time, and then eventually leak. Not to mention all the teflon particals that will clog your filters.

I will be taking the system apart over the winter and clean and replace all the fitting''s coatings with their diesel rated product.
08-27-2004 10:42 AM
Use of Teflon Tape on fuel fittings

Teflon in a fuel system is a bad idea all together. It would be safer to use some of the gasket compounds(silicones) that are sold in auto parts stores, make sure they are formulated to be used with oil and fuel applications.
08-22-2004 07:16 PM
Use of Teflon Tape on fuel fittings

RichH, thanks so much for your input, but now I''m no better off than when I first asked the question. I have two opposing views on the subject from folks who have totally different experiences using Teflon Tape and Teflon Compound. What is a guy to do?? I would encourage both of you to respond and others too on their experience using Teflon Tape and Teflon Compound on fuel fittings. I do appreciate your response. Thanks, Peter
08-19-2004 10:49 AM
Use of Teflon Tape on fuel fittings

Better to use teflon tape than teflon pipe dope.

Less chance of the ''carrier'' in PTFE pipe dope from dissolving leaving the PTFE particles free to migrate down the piping stream. PTFE dope is notorius as a ''particle generator, PTFE tape wont ''particulate''.
08-19-2004 05:55 AM
Use of Teflon Tape on fuel fittings

Silmaril, thanks so much for the warning. I use Teflon tape in my job, Landscape Maintenance. When I began replacing my fuel system I automatically reached for the Teflon tape. I stopped and asked the question and am sure glad I did. Thanks again. I''ll go get some Teflon pipe dope/compound before going any further. Regards, Peter
08-16-2004 07:08 AM
Use of Teflon Tape on fuel fittings

Don''t do it!!! I just installed (then re-installed) a complete new fuel system on my 37'' sloop. Everything new, from the deck filler, right through to the lift pump on the 3GM30F, and new return lines as well.

I used teflon tape the first time through, I have some 1 1/2" npt bronze fittings going from the tank through a bulkhead to the fuel hose. Each one leaked just a drop when the system was filled for the first time.

I then had to drain the tank and take everything out, clean it, and re-assemble it all over again. This time I was using Teflon PIPE DOPE/JOINT COMPOUND, and my biggest stilson wrench to ensure that everything would be tight and leak free.

On pipes under 1 1/2", just coat the male threads and sock them down good and tight. On 1 1/2" and up, coat both male and female and tighten well. Be careful to not go overboard using too much pipe dope, as excess will clog up your first filter.

Good luck.
08-16-2004 06:57 AM
Use of Teflon Tape on fuel fittings

When installing national pipe thread fittings on a diesel fuel system is it a good idea to use Teflon Tape?

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

For the best viewing experience please update your browser to Google Chrome