SailNet Community - Reply to Topic
Thread: How to bleed hydraulic steering? Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.

User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

  Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below

  Topic Review (Newest First)
01-31-2009 09:13 AM
boatpoker Not all rams have bleed valve so you may have to crack the union on one line at the ram and have someone turn the wheel back and forth (full cycle) and fill the helm pump at the same time. The second person must remain at the ram and tighten the nut when air ceases to bubble out. Crack the other nut at the ram and repeat. This can take five minutes or 1hr. depending on length and angle of lines. You may have to go back to the first nut on the ram and repeat one time. I just installed a new hydraulic system by myself and it was a major bitch running back and forth from the helm to the ram.
01-31-2009 08:37 AM
Ilenart A couple of years ago I helped my mechanic to bleed the hydraulics after a ram service and he got me to spin the wheel first one way with a bleed valve open, then he closed that valve and opened another one & I spun the wheel the other way. We did this 3 or four times until only hydraulic fluid came out. Has worked fine for the last two years. Definitely a two person job.

01-30-2009 12:46 PM
brak for the first rough bleed, you have to open "bleed valves" on the hydraulic ram, and then turn the wheel until air stops coming out. that will get the major bubbles out, but the system will still have enough to be "soggy". There are all sorts of contraptions that promise to suck the air out (connecting to bleed ports on the ram and to the fill port), but it really does not seem possible to me to fully bleed the system that way. On mine, bleed valves would re-admit some air back in when open by their very nature.

After a primary bleed I usually let it stand for a while, so that air would move upwards towards the steering pump. then, just turn steering all the way to one side and another, alternating - depending on your setup the air would escape from the fill port. My hoses run fairly level, and having a boat sway a bit (at anchor or some such) helps shuffle air around Or just shake the hoses by hand if they are rubber or plastic.

Initially I had a funnel with hydraulic fluid fitted to fill port and bubbles escaped into funnel, while fluid went into the system. Since I added a small reservoir, bleeding seems to have become unnecessary - air just moves upwards into the top of reservoir on its own, all I have to do is top it off may be once a season (though it only had been a season since I installed it).
01-30-2009 11:57 AM
jrd22 I have ususally been able to get most of the air out of the system by just turning the helm pumps back and forth a bunch of times. You need to check the fluid level while doing this and add to keep from pumping more air back in. If you have high spots in the lines you may need to crack some fittings loose to release air that can't get back to the pump. If possible fill the cylinders with fluid before you hook up the hoses. Hopefully someone else has an easier way, it can take a while to get all the air out if you have long runs or more than one helm station.
01-30-2009 11:47 AM
How to bleed hydraulic steering?

I had replacements made for all 4 hoses on my Teleflex hydraulic steering. The boat is a Formosa 51. All the hoses had "aneurysms" and I figured it was only a matter of time before failure. Now I am trying to figure out how to bleed the air out of the lines and rams. I can't figure out how to do it since both rams are dual action. If anyone has experience/advice it would be appreciated.

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

For the best viewing experience please update your browser to Google Chrome