SailNet Community - Reply to Topic

   Search Sailnet:

 forums  store  


Quick Menu
Forums           
Articles          
Galleries        
Boat Reviews  
Classifieds     
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Charts
Clothing
Electrical
Electronics
Engine
Hatches and Portlights
Interior And Galley
Maintenance
Marine Electronics
Navigation
Other Items
Plumbing and Pumps
Rigging
Safety
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here






Go Back   SailNet Community > Boat Builders Row > Helms > Removing teak plugs
 Not a Member? 


Thread: Removing teak plugs Reply to Thread
Title:
  

By choosing to post the reply below you agree to the rules you agreed to when joining Sailnet.
Click Here to view those rules.

Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Topic Review (Newest First)
03-30-2009 01:37 PM
Capnblu I don't like the drill/screw method. Sure it works in many cases, but there will always be a few that blow out the surrounding good teak. I found the best method so far is to use a sharp carving knife with a 1" long blade. going with the grain of the bung, insert sharp blade into bung gently at a 45 degree angle. You will get a little chip out of the bung, now work you way across the bung progressively deeper till it pops out. Sometimes it's necessary to go at it from both sides of the bung, working towards the center.
03-30-2009 10:28 AM
quidam1947 The way you suggest should work fine but take care that you don't bugger-up the screwhead underneath as you never know for sure how deep the bung-hole actually is, in some cases.

We've simply used a woodworking scratch awl to gently pry up old bungs poke straight down in the center of the bung. Pry one direction with the grain and then pry side-to-side taking care NOT to damage the perimeter of the bung hole.

After you've done the work needed. Make sure the hole is clean (vacuum) and then seal the new bung in place by dipping the end in a little varnish (I pour a little in a pie tin wipe excess off by dragging the drips on the side of the plate). LINE UP wood grains and tap in place with a rubber mallet.
Knock ends off sticking up after its cured a bit with a sharp chisel taking care to keep the angle above the plane of the trim piece.
03-30-2009 10:12 AM
Wayne25
Removing teak plugs

I'm removing the teak companionway trim, handrails, etc. to acid wash and recondition. I've never removed a good teak plug and replaced with a new teak plug before. I've read the best way to remove them is to drill a pilot hole in the center of the plug and drive a small screw in the plug that will extract the plug when it bottoms out on the existing screw head. Is this the best way? Any other tricks?

I have new 3/8" plugs for when I'm putting everything back together. I assume they are held in with more than friction fit. Waterproof glue sounds too permanent. What is the correct procedure and what sealant if any is used to hold the new screw plug?

 
Posting Rules
You may post new threads
You may post replies
You may post attachments
You may edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On


All times are GMT -4. The time now is 07:31 PM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) Marine.com LLC 2000-2012

The SailNet.com store is owned and operated by a company independent of the SailNet.com forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.