SailNet Community - Reply to Topic

   Search Sailnet:

 forums  store  


Quick Menu
Forums           
Articles          
Galleries        
Boat Reviews  
Classifieds     
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Charts
Clothing
Electrical
Electronics
Engine
Hatches and Portlights
Interior And Galley
Maintenance
Marine Electronics
Navigation
Other Items
Plumbing and Pumps
Rigging
Safety
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here






Go Back   SailNet Community > On Board > Gear & Maintenance > A few questions before my deck recore project...
 Not a Member? 


Thread: A few questions before my deck recore project... Reply to Thread
Title:
  

By choosing to post the reply below you agree to the rules you agreed to when joining Sailnet.
Click Here to view those rules.

Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Topic Review (Newest First)
05-08-2009 09:22 PM
scottyt sorry you are going to have to taper out the non skid to glass the outer surface back on. i would cut it right at the edge of the non skid, use the one inch smooth area as the taper on the out side of the cut

edit by taper i mean the bevel you will have to grind when you go to glass it back in
05-08-2009 08:43 PM
tommays J/24 #140 - Renovation

Down at the bottom there are a lot of recore pcitures
05-08-2009 08:35 PM
Perithead
A few questions before my deck recore project...

I have a South Coast 22 that I am restoring, my next chore is to recore the bow decking because it is very soft. I drilled a small hole in the center and the wood core was pretty damp so you all konw what that means. I think it should be totally redone so I don't plan on just drilling holes and filling it with epoxy.

Photobucket

The entire bow deck is soft so I am going to cut out the top layer of fiberglass and remove and replace the core then fiberglass the original piece of decking back on.

My question though is where should I make my cut? I know I need to cut the entire peice off, that would be no problem. The problem would arise when I go to glass the peice back on. As you can see in the following photos, there isn't alot of "smooth" deck space between the edge of the deck where the hull to deck joint is and the non-skid pattern.

Photobucket
Photobucket
Photobucket

All around I have about a 1" lane of smoothness to cut in.

When I go to glass it back I want it to be as easy as possible. I do not want to have to grind away any non-skid and I don't want to have to glass over it. I also would like to avoid having to glass down the outside corner just above the hull to deck joint.

Lets say I cut in the center of my smooth "lane" then that would leave me about a half inch on each side of the cut to grind out and adhere my fiberglass back to, would that be enough?

Thanks everyone for your replies!

 
Posting Rules
You may post new threads
You may post replies
You may post attachments
You may edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On


All times are GMT -4. The time now is 01:20 PM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) Marine.com LLC 2000-2012

The SailNet.com store is owned and operated by a company independent of the SailNet.com forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.