SailNet Community - Reply to Topic
Thread: Adjustable backstay of a masthead rig? Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.

User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

  Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below

  Topic Review (Newest First)
07-01-2009 08:56 AM
Faster If you've got hydraulics, keep it. No tackle arrangement is likely to do as good a job as easily and conveniently. Rebuilding a cylinder shouldn't break the bank.
07-01-2009 12:39 AM
blt2ski You might look at the Harken site, their is a "compuspec" link, that will spec out an appropriate adjuster for you, based on your boat, type of sailing you do ie heavy air, racing etc.

Otherwise, it is a complete SWAG on all our parts.

07-01-2009 12:26 AM
j34035 It takes a lot of mechanical advantage to = a hydraulic adjuster. While I had mine off for a rebuild, I had a 4/1 (not really much) on the backstay and it would not even affect the headstay sag. The hydraulic will pull the headstay, and I can bend the mast on my J/34c (masthead rigged) completely out of column if I want. I like my hydraulic. I had Westmarine rigging shop rebuild mine.
06-30-2009 11:55 PM
OhioTom Thanks for the replys. I think I'll take a good look at the hydraulic adjuster to see if its worth it to rebuild. If not, I'll just convert it to a block and tackle adjuster. Any idea what mechanical advantage I would need?
06-30-2009 08:05 AM
SEMIJim Yes, a backstay adjuster does make sense on a masthead rig. While it can't perform to bend the mast like it can on a fractional rig, it will bend the mast a bit, and it'll definitely tighten the forestay. We have a backstay tensioner on our Pearson P30, and we use it. In fact: I used it in a race two weeks ago Sunday: Tightening it on the beat and easing it somewhat on the reach.

06-30-2009 07:49 AM
tommays I sail on a masthead C&C 35 with hydraulic backstay and baby stay and it bends like a J24 mast
06-30-2009 07:47 AM
paulk If you have a Soverel 26, the mast is designed specifically to be tweaked to accommodate various conditions you will encounter. It has a rather spindly spar, on purpose, to allow for this. Removing or degrading equipment will not enhance the boat's performance and will likely reduce potential resale value. Go to the Soverel 26 website to learn more about how to use all the bells, whistles and strings. There are lots on Soverels.
06-30-2009 05:48 AM
OhioTom The boat is a Soverel 26. It also has a baby stay with a fiddle block for tensioning. Again, I'm wondering if this setup can really bend the mast enough - without causing too much strain on the rig/boat - to actually flatten the sail enough to make any practical difference.
06-30-2009 02:59 AM
knuterikt You dont say what kind of boat you have, it could be helpful.

The backstay is used to controll the bend in the mast and to a degree the forestay tension.

But to make this possible you will need a masthead fitting on the mast where the attachement of the backstay are placed some inches (6?) further aft than the aft wall of the mast section. These masthead fittings are also angled so the aft part sits higher than the forward part.

With a setup like this the mast should be adjusted with a little bit of prebend in the mast.

I would gess that since you have the setup you described your mast is of this construction.

I would not remove the hydraulic backstay adjuster on my boat. If necessary it should not cost so much to service the adjuster.

You can replace the rod with wire (I have a wire backstay with hydraulic tensioner).

On my boat adjustable length on the backstay tensioner is so short that I have to put in some bend in the mast before I can connect the backstay to the backstay tensioner (the base prebend)
06-30-2009 01:09 AM
blt2ski WHile you do not get the control etc of a fractional rig, you can still tighten up the forestay a bit more, which IIRC pulls the draft forward some{it might be back, but don't quote me], removing/lessoning weather helm a bit. I have pretty good success with my MH rig tightening up the back stay. I am able to bend the mast some, not like a fractional can, but I can create some mast bend, to help the sail in heavier winds.

This thread has more than 10 replies. Click here to review the whole thread.

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

For the best viewing experience please update your browser to Google Chrome