|Topic Review (Newest First)|
|07-02-2009 06:16 PM|
|bobmcgov||Like most SJ21s, ours has soggy balsa. I just finished drilling and filling all the deck hardware; added large backing plates; and now we're going to sail it. Maybe a re-core next year. But it'll do for now. No high heels on deck!|
|07-01-2009 11:21 PM|
I used a moisture meter to scope out my deck. Took a eraseable, whiteboard marker and just started measureing and writing down numbers. I did this all around the cabin and near the chainplates first. The numbers were REALLY bad.
So it REALLY pays to know what the numbers are - and what the mositure is... My boat would not be one someone else wouldwant to restore.
Just pays to know. ALso to look for corrosion. It is QUITE POSSIBLE to snap those stainless steel rig mounting plates - right in half. USUALLY - where you cannot see them.
If there is a lot of moisture, then you might look for all the other related problems.......
|07-01-2009 05:52 PM|
I am with the "sail it" brigade and I think you should just go with it in the meantime. If I was in your position, I would go for the "drill and stabilize" option. You could get many years of excellent sailing out of your boat wthout a huge amount of work.....
|07-01-2009 12:41 PM|
|mjrogers||Well, I like what I'm hearing. The forward lower shrouds are close to the rot but sound OK when I tap the deck though there is no guarantee they won't "pump" from wind and wave action. I have enough time to pull the forward chainplates for inspection and reinforce as needed. I'll Inspect the other chainplates and stem fitting closely and if they are OK I'll declare "Damn the core-rot, full speed ahead!" Thanks, Michael|
|07-01-2009 11:24 AM|
MJ, Given that your stays and shrouds are attached at stout and uncompromised structures, I would say you can sail her like you would if she were brand new. Get the rigging tensioned appropriately and have fun.
If you start seeing the deck peel up at the headstay chainplate or you're taking on water through your shroud chainplates, then you have a problem that needs attention.
One good thing about the C22 is that you don't have a fortune invested in her. And even if you get to the point where you can't safely sail her, you can part-out the boat and at least recoup some of your investment. Big market out there among C22 sailors for parts, project boats, etc.
Don't disappoint your wife. She needs you to make her a home. In the meantime, I'll wager she will be happy to have you spend some time rehabbing your boat if you want to.
|07-01-2009 07:39 AM|
|CaptainForce||Most vessels are designed with the structure of the hull and rig not dependent on the deck. I believe most surveyors would consider this a cosmetic problem as opposed to a structural problem. I think you would be able to get away with option three and not even be extra "gentle" except for no "rhino stomping" on the deck. 'take care and joy, Aythya crew|
|07-01-2009 07:29 AM|
So, we have one vote for sail it and sell it. That is my real question. Is this boat safe to sail conservatively?
If it were a small area I would drill and inject, but I am suspicious of the entire foredeck as well as the vertical face forward on the cabin. I suspect it would take less time to cut the deck than it would to drill all those holes.
I haven't done a repair like this but, I was a journeyman (approaching master) carpenter in my first career, so, I'm good with my hands and could probably do a decent job. I just don't have time for another big project. We have an ancient house which we are remodeling and like an idiot I told my new wife that I was a good carpenter. She's a doll and it is impossible to turn her down.
|06-30-2009 09:37 PM|
Originally Posted by DwayneSpeer View Post
|06-30-2009 09:34 PM|
Originally Posted by mjrogers View Post
I have had buddies ask me to bring my moisture meter along when I arrive for a sail. They are always amazed at how much moisture we find..
Personally, based on your future plans, I would say to sail it now then sell it as is. You may actually further reduce the value by cutting up the decks if you are not proficient at fiberglass repairs. I would be very wary of buying any boat with DIY deck repair unless I had a full stack of photos to asses the techniques used.
I vote for sail it and then sell it..
|06-30-2009 09:30 PM|
|sailingdog||IF the area is larger than about a square foot... you really should re-core the area.|
|This thread has more than 10 replies. Click here to review the whole thread.|