SailNet Community - Reply to Topic

   Search Sailnet:

 forums  store  


Quick Menu
Forums           
Articles          
Galleries        
Boat Reviews  
Classifieds     
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Charts
Clothing
Electrical
Electronics
Engine
Hatches and Portlights
Interior And Galley
Maintenance
Marine Electronics
Navigation
Other Items
Plumbing and Pumps
Rigging
Safety
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here






Go Back   SailNet Community > On Board > Gear & Maintenance > Hull Core Repairs, Post Blister Repairs
 Not a Member? 


Thread: Hull Core Repairs, Post Blister Repairs Reply to Thread
Title:
  

By choosing to post the reply below you agree to the rules you agreed to when joining Sailnet.
Click Here to view those rules.

Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Topic Review (Newest First)
04-18-2005 06:08 PM
sailingfool
Hull Core Repairs, Post Blister Repairs

Best of luck with whatever way you go, but I gotta say that these posts provide an opportunity to harken back to numerous previous threads about the risks of cored construction in hulls. I''ve become a firm believer in all glass, and the idea of personnally patching a hull that will then take my family many miles from shore is quite a leap of faith.

Good luck.
04-18-2005 03:19 PM
LH44
Hull Core Repairs, Post Blister Repairs

I have just completed replacing approx 10 sq foot of balsa core in the bottom of a J36. I did the repair from the outside and started by removing the outer laminate and the rotted balsa core. The interior laminate showed holes from cabinetry screws, etc.

I did the repair as follows:
1. Wetted out the interior laminate and new balsa core with neat west system epoxy.
2. Prepared a mixture of resin and collodial silica to a thick consistency and then coated the interior laminate.
3. Allowed the squares of balsa core to open up over the edge of a table, and filled all of the joint lines (in both directions) with the thickened mixture.
4. Pressed the balsa core in place and was presently surprised in that it did not need any support even though it was a vertical surface.
5. Then proceeded to glass a new exterior laminate to the exterior of the balsa core.

By adding glass over the interior of your exterior laminate, i do not think your cores will line up properly and you run the risk of creating a hard spot. The thickened epoxy mixture will more than provide "insurance" against your exterior work as well as assure a good bond with the balsa core.

04-13-2005 09:41 PM
CJV
Hull Core Repairs, Post Blister Repairs

Hello,
My Tartan Ten (hull #282, 1981) had a blister problem repaired before I bought her in May of 2004. She also had a core delam problem which I am now repairing. After removing the inner skin and affected core, some of the putty-filled blister repair holes on the now-exposed inside surface of the outer skin are visible. They show up as perfect white circles about 1/8" in diameter. In two cases they are missing altogether so you can see clear thru the hull.
I''m wondering what''s the best way to proceed when re-coring:
1. Glass over all affected areas with epoxy & glass fabric, essentially thickening the skin but ensuring no further mechanical separation of the putty.
2. Ignore it and lay new core above those areas.
3. Grind and fair from the outside the areas with blister repairs.
4. Grind from the inside and fill/fair with putty, then glass another surface in before applying core material.

As far as I can see, #1 would make most sense. Am I over-engineering this fix?

 
Posting Rules
You may post new threads
You may post replies
You may post attachments
You may edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On


All times are GMT -4. The time now is 09:58 PM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) Marine.com LLC 2000-2012

The SailNet.com store is owned and operated by a company independent of the SailNet.com forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.