SailNet Community - Reply to Topic

   Search Sailnet:

 forums  store  


Quick Menu
Forums           
Articles          
Galleries        
Boat Reviews  
Classifieds     
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Charts
Clothing
Electrical
Electronics
Engine
Hatches and Portlights
Interior And Galley
Maintenance
Marine Electronics
Navigation
Other Items
Plumbing and Pumps
Rigging
Safety
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here






Go Back   SailNet Community > On Board > Gear & Maintenance > Engines > Diesel > Leaking intake gasket caused by too much blow-by?
 Not a Member? 


Thread: Leaking intake gasket caused by too much blow-by? Reply to Thread
Title:
  

By choosing to post the reply below you agree to the rules you agreed to when joining Sailnet.
Click Here to view those rules.

Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Topic Review (Newest First)
08-18-2009 10:11 AM
preservedkillick Just a follow up.

Went to the boat, ran the engine and could feel pressure & exhaust coming from the intake manifold gasket. Replaced the gasket, didn't change a thing. Checked exhaust mixer elbow, clean. Running the negine again, feeling more carefully, found an injector near intake manifold was leaking. Took the injector out, found carbon gunk at the bottom where it seats on a copper ring. I cleaned up the carbon as best I could and put it all back together..runs fine. I had no idea an injector could leak like that.
08-11-2009 09:08 AM
trantor12020 your exhaust manifold or mixing elbow is choked.
08-09-2009 10:26 PM
Capnblu If your intake manifold gasket is leaking, it would be a vacuum leak. Blow by refers to combustion gasses entering the crankcase, past the piston rings. If your exhaust valve stems were leaking, you would have some blow by into the valve cover, but not much. If your intake valve stems were leaking, you would be pulling oil into the combustion chamber, and probably notice smoke in the exhaust. I suspect your exhaust manifold / heat exchanger gasket is the culprit remove it clean the surfaces, and install a new set. Torque to mfg. specs, and then after 10 - 15 hrs, retorque.
08-09-2009 04:27 PM
preservedkillick I thought of those two things too. Valves..I'll get a mechanic if it comes to that. I'll check the exhaust elbow when I go back this week.

I've done some research, and it appears that some blow by pressure is normal. Based on what I've read in the diesel car forums, lots of pressure along with smoke is a bad thing. But, I wonder, what is considered normal. I'm not getting any smoke that I can see, although I did get a little soot near the leak.

I don't think I'm burning any oil, although I can only say that I've burned none in the 20 hours or so I've put on the engine since I've owned it. Oil looks ok, coolant looks great. Both changed this spring.

Thinking more about it, I don't quite get how the gasket could have failed as a result of the blow by. Granted the leak is at the intake manifold right near where the blow by hose connects, but the intake manifold should have no pressure..the air intake is right there.

My plan so far is to check the exhaust elbow, replace the leaking gasket (if I can get one from Vetus) and keep an eye on it. I'd also like to get a compression test done.
08-09-2009 04:25 PM
Selkirk I think you're actually looking a little too far into the woods. I believe all you have is a failed gasket.

Why did it fail? I dunno. But it did, and that's the first thing I'd fix.
08-09-2009 11:01 AM
timebandit Partially plugged exhaust system or valve adjustment?
08-09-2009 09:53 AM
preservedkillick
Leaking intake gasket caused by too much blow-by?

Motoring yesterday, I noticed the smell of exhaust in the engine compartment. Took a look and it appears to be leaking exhaust out of the intake gasket. Bit of black soot near where the leak is.

Now, when starting the motor, there's a distinct "air sound" before it actually fired up. There's a blow-by hose that goes from the cover to the intake manifold (near where I think the leak is), if I take put my finger over the end of the hose with the engine running, within a few seconds I can feel the pressure building up. What's normal?

This sounds bad. Rings? Valves? Any chance there's a valve somewhere, like a PVC valve? I don't see one.

This seems to be a sudden thing, it's been running well, with no sign of trouble before yesterday.

This is a 10 year old diesel Vetus 310 with less than 400 hours reported.

 
Posting Rules
You may post new threads
You may post replies
You may post attachments
You may edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On


All times are GMT -4. The time now is 07:29 PM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) Marine.com LLC 2000-2012

The SailNet.com store is owned and operated by a company independent of the SailNet.com forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.