SailNet Community - Reply to Topic
Thread: Rigging tension meter Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.

User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

  Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below

  Topic Review (Newest First)
08-17-2009 07:55 PM
rigging tension meter mark II

I have the mark II tension meter, however I have lost the spacer. My boat's wire is 3/16 from what I gather you need the rod and the spacer to establish the settings.
Can some one provide me with the thicknes of the spacer so that I have fabricate one.


06-11-2009 12:48 PM
Originally Posted by fazzollini View Post
The rigger who did my boat put so much weather helm that the boat turns up into the wind with a good puff.
One assumes you mean when you're close hauled or on a close reach. That's normal--to a degree.

Originally Posted by fazzollini View Post
I also think i'm loosing a lot of speed because i'm using to much rudder pointing.
More than about five (5) degrees? If so: Then yes.

Adjusting the rig really isn't all that hard. Two, no, three resources: Giu's ]Adjusting Your Rig How-To (I'd post the URL, but Sailnet's brain-dead software will destroy it - it's a sticky at the top of the Gear and Maintenance sub-forum), Ivar Dedekam's book: Sail and Rig Tuning, and a Loos gauge (I recommend spending the extra for the "Pro" model) and you'll be good to go.

I did our's last season, for the first time ever, w/o a Loos gauge. I came close. She performed adequately. Better than the season before, anyway. Helm had just a touch of weather in it. This year I had a Loos gauge (thoughtful birthday present from The Admiral). This season The Admiral has already commented on how she points higher and the helm is as good as last season, if not better.

It is amusing to let go of the tiller entirely, while we're going up-wind, and watch it just sit there, vibrating gently The first time The Admiral did that, last season, she goes "Look." I looked, and my eyes about popped out of my head. "Well, hon, I guess I got the rigging about right..."

06-11-2009 10:36 AM
Big help Thanks

The rigger who did my boat put so much weather helm that the boat turns up into the wind with a good puff. I also think i'm loosing a lot of speed because i'm using to much rudder pointing. Thank a lot for the help.
06-10-2009 07:02 PM
Lipton Tension Meter Mk II

Yes, I have the reference chart but it is just lines in which you input your readings. Is this what you are looking for? These are the instructions that came with the chart.

Tension Meter Mark II


Keep the Mark II Tension Meter well lubricated with a light weight non-gumming oil to achieve maximum sensitivity.

The Mark II Tension Meter is adjusted to standard by snapping the supplied steel rod into place(with preloaded spacer in place next to the spring) and turning the knurled knob until a reading between 1 and 1 is achieved with the cylindrically formed end of the knob at right angles to the axis of the test specimen

Recommended values (based on standard setting of 1 to 1 )

3/16 wire to 1
1/4 wire 1 to 2
9/32 wire 2 to 2

For light wire the Mark II tension Meter is adjusted using the standard rod (no preload spacer) and to a reading of 2 to 3

Recommended values (based on standard setting of 2 to 3)

3/32 wire to
1/8 wire 1 to 1
5/32 wire 2 to 2

When this initial adjustment has been made, pairs of shrouds should be adjusted using the Mark II Tension Meter until their tensions are equal.

To get the most out of the Mark II Tension Meter, keep a permanent record of readings for which the adjusting table has been provided. This permanent record may include optimum settings of fore and back stays.

To maintain maximum performance, check the tension readings of the shrouds and stays periodically against your permanent record.

An eye is provided for a lanyard which should be bent onto the stay being tested or on your rest.

Lipton Marine Industries, Inc.
Rock Ridge, Mamaroneck, N.Y. 10543
06-10-2009 02:36 PM
Lipton Marine Mark II

I also have a Mark II. Does anyone have a referance chart for it.
05-29-2009 02:38 AM
groundhog How much were these things originally?

I recently saw a gauge that you hook around the wire on the two outer ends and there is this spring loaded "finger" that pushes on the wire in the middle. Then the arrow points to a number from zero to three?

Is this a good meter? What else is needed to make it work? Obviously some type of table or such.
05-28-2009 03:08 PM
charlierusty1234 I can help if anyone is still looking.
01-27-2007 02:42 PM
Wayne25 gc1111

Yes, I have the calibration rod also. But there must be some type of table that tells you what the readings mean. For example-lets say you want to adjust a 5/32 shroud to 10% of it breaking strength. I can find out what that number is from the wire manufacturer, but how does that number relate to the tension meter? Do you have instructions with it?
Also, the tip that has the ridge that contacts the shroud looks a little worn on mine and it looks replacable. Any idea if these are still available? It looks like a very expensive meter. I would hate to have to go out and buy a Loos meter.
01-27-2007 01:46 PM
gc1111 My boat came with one of these also - but also without the calibration rod. But it is still valuable for balancing the tension between stays on different sides and general comparison (is this shroud set up harder than that one?).
01-27-2007 01:34 PM
Rigging tension meter

When I bought my boat, it came with a "Mark II Tension Meter" made by Lipton Marine Industries to set up the standing rigging. I found a Lipton Marine Industries on the web but they don't make anything like the tension meter and couldn't help me. Does anyone own one of these, have the manual or can tell me how to use it. It doesn't have the same scale as a Loos meter and uses a rod for some type of calibration and you take a percentage of this reading. It probably had some type of table or graph with it originally.
Thanks for your help.


Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

For the best viewing experience please update your browser to Google Chrome