SailNet Community - Reply to Topic

   Search Sailnet:

 forums  store  


Quick Menu
Forums           
Articles          
Galleries        
Boat Reviews  
Classifieds     
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Charts
Clothing
Electrical
Electronics
Engine
Hatches and Portlights
Interior And Galley
Maintenance
Marine Electronics
Navigation
Other Items
Plumbing and Pumps
Rigging
Safety
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here






Go Back   SailNet Community > On Board > Gear & Maintenance > Sanding / painting on a cradle
 Not a Member? 


Thread: Sanding / painting on a cradle Reply to Thread
Title:
  

By choosing to post the reply below you agree to the rules you agreed to when joining Sailnet.
Click Here to view those rules.

Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Topic Review (Newest First)
09-28-2009 05:12 PM
jjablonowski First off, I'm a cruiser---not a racer---so I'm not Fanatical about bottoms.

Four pads at 25 sq. in. apiece ain't gonna make a whole lot of difference to me, compared with the entire bottom.

So I leave a small soda bottle half full of bottom paint, along with a disposable foam brush, hanging in a ziplock bag from one of the jackstands. When they launch in the Spring, the yard crew lifts the boat with their straps, then touches up where the pads were.

Does the fresh paint have time for a proper cure? Probably not. But next season the chances of having the jackstands placed in Exactly the same spot are, well, ....
09-28-2009 10:15 AM
JimsCAL When I stored my 7000 lb boat on a cradle with 4 pads, I routinely used one stand on the centerline (near bow or stern) to permit backing off the nearby two pads for sanding and painting. After my work under each cradle pad, I would screw it back to within a fraction of inch of the hull just in case until the bottom paint dried. Never had a problem.
09-28-2009 07:58 AM
cghubbell Thanks! Doesn't sound too bad at all. Hopefully I can borrow a pair from the yard I'm in so I don't have to buy them for a short term project.
09-25-2009 07:05 PM
Sabreman It's only 6800 pounds, what could go wrong?

Keep in mind that the weight of the boat should be resting on the keel, so the pads are only holding the boat upright. You're on the right path, but will be a bit constrained by the cradle frame.

Take two jackstands and an appropriate length of chain. Position one on each side of the boat immediately forward or aft of the cradle pad as appropriate. Put 1/2" plywood under each corner of the stand. The base of the jackstands are triangular; position the stand such that they are angled in toward the hull and the points of each base are pointing toward each other (look around the yard at other boats for an example).

Connect each stand with the chain. THIS IS EXTREMELY IMPORTANT - the stands can be pushed away from the boat if not chained together. Raise the pads on each jackstand so that the contact the hull. Take up all the slack on the chain, and pull the stands away from the boat to take up any remaining slack. THIS IS IMPORTANT.

Tighten the jackstands as much as you can by hand. They should not be supporting the boat. Now take a deep breath. Loosen ONE pad on the cradle a little bit, give the boat a good push with both hands to make sure that it doesn't shift. Keep backing off and shoving until the pad is away from the hull. The idea is to make sure that the jackstands are solid and not going to move.

Do the work that you need to under the pad, then restore the cradle pad to the original position. Repeat the procedure for each pad. Alternately, you may be able to take pressure off both forward cradle pads and do your work, but I would restore the cradle pads at night or extended periods.

I've done this many times and it's not that bad. I don't have a cradle, so I'm not as constrained by space. I personally don't like cradles since I can't add pads where I want them.
09-25-2009 02:52 PM
cghubbell
Sanding / painting on a cradle

My new (to me) boat is currently on a cradle and about to begin a fun pox repair session. What is the safe / recommended method for handling the hull area that's currently under the cradles 4 pads?

Do I just find a single boat jack, place it close to the current cradle pad, chain it to the opposite side of the cradle, then back off the cradle pad's threaded rod to get it out of the way? My cradle's "legs" that the boat sits on have the same kind of threaded rods that the top of boat stands use.

Having never worked on a boat in the cradle it's a bit unnerving having all that boat over my head and wondering if my idea is structurally safe I'm sure it's not as bad as it seems, but I have a pretty vivid imagination that depicts 6800 lbs falling off the cradle being a bad thing!

 
Posting Rules
You may post new threads
You may post replies
You may post attachments
You may edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On


All times are GMT -4. The time now is 02:49 AM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) Marine.com LLC 2000-2012

The SailNet.com store is owned and operated by a company independent of the SailNet.com forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.