|Topic Review (Newest First)|
|12-17-2010 09:27 PM|
Neil, did you ever get a pic of the mast step? Reason I ask is I just bought a B34 and will be doing a lot of work to bring her back to life.
|12-03-2009 04:05 PM|
Rigrite: Lost cause.
Halsey H: yup that was the next possible step.
Otherwise: I going to take the mast trimmings and glue it to a piece of pipe. Then run it thru the partners down to the foot and take measurements, then have the new foot milled out of 1-1/4" aluminum block or 3/4" stainless.
I would still like a pic of a good keel stepped foot in place as a reference.
|12-02-2009 12:56 PM|
The Bristol 34 was designed by Halsey Herreshoff who is still living and who had a website not that long ago. I don't know if this is current but I had this email firstname.lastname@example.org You might email him for advise.
|12-02-2009 11:59 AM|
|deniseO30||did you ck with riggrite.com? they may have what you need. I've heard they are difficult to deal with though.|
|12-02-2009 10:22 AM|
Mast: Yes I'm using the trimming for the new foot template.
Rigging: the rope is good but a few swages are cracked so we're reswaging all and trimming down the rope, mainly the shrouds. The stays have extender plates.
|12-01-2009 09:11 PM|
I've got to cut about 1-1/2 to 2" of nastiness off the bottom of the mast.[/QUOTE]
Sounds like a plan. I would cut mast first that way you know how much you have to build up the Mast step when you mill the aluminum block . Unless you replacing all the standing rigging. If you replacing the standing rigging you could re-rig to the new shorter mast height.
|11-30-2009 12:24 PM|
|FishmanTx||I was gonna mill a piece of aluminum block myself and customize it to fit. The original studs are shot and won't be reused for mounting but will be used for holding the poured epoxy "bedding" for the new foot. New 316SS studs(bolts) will be put in to mount the base. Also, I've got to cut about 1-1/2 to 2" of nastiness off the bottom of the mast.|
|11-28-2009 07:47 PM|
Originally Posted by FishmanTx View Post
How does the bottom inch or so of the mast look? I have often had to cut a little off the bottom to get to clean metal and have had the new step built up to compensate for the loss of height.
|11-27-2009 10:32 PM|
The mast step on my B28 is stainless steel. I do not have a pictures but it about 1" wider than the mast on each side and about 2" Longer front and back. It has 4 raised places on the inside were the mast would sit to hold it in the center of the plate. it has 4 holes one in each corners so you can Lag bolt it down to the Keel. Had to trim mast 1/4 to remove some corrosion after 30 years. We then but 1/4 aluminum plate under the step separated with a be a piece of plastic. If I make to the boat this weekend I will see if it can get a picture.
|11-27-2009 06:29 PM|
Bristol 34 Mast Step....Help!
Does anyone out there have a pic of 34' mast step in place (keel stepped) or the measurements? We pulled the fragments and the rust pile that used to be our step out of the bilge and it's totally shot! Steel plate used to be around 9"x14", 1" or so thick and slotted fore and we think aft as well but it's hard to tell. The steel had rusted and "delaminated" and crumbled in our hands. We need to fabricate a new one, probably from aluminum block and have it milled.