|Topic Review (Newest First)|
|12-17-2009 01:13 AM|
Or 2 headsails not on roller furlers.
|12-17-2009 12:50 AM|
Sloops may sail better, be easier to maintain, and be simpler overall...but, cutters are just plain ol' prettier. Does one really need a better reason to have a staysail in the foretriangle?
|12-17-2009 12:24 AM|
One thing that wasn't mentioned here...maintenance. More sails means more sailmakers bills, more rigging to inspect/replace, more furlers that can get jammed/break bearings, more sheets to lead aft, more holes in the deck to leak, more tension points on the mast...etc. Just more overall systems complexity in general
That being said, there is much to be said about the flexibility by having two headsails on roller furlers during a blow...
|12-16-2009 10:06 PM|
At least it's the kind of information that anyone can use today. It's worse when someone asked an obscure question in 2002 and somebody answers it today.
|12-16-2009 08:29 PM|
|krozet||This has to be a record... Responding to a post over 7 years old?|
|12-16-2009 06:57 PM|
|KyLeah49||I have sailed on a 48' cutter with a 150 genoa. While running, or on a reach, we used the staysail. When beating or close hauled, we furled the staysail and brought the genoa out to 150 as if we were a sloop. It seemed to work for us. So I agree that a cutter rig does offer more versitility that a straight sloop.|
|04-29-2002 04:06 AM|
Cutter rig vs. sloop rig
Rigs-cutter vs. sloop rig
Today these terms are used quite loosely as compared to their more traditional definitions. Traditionally the sloop rig was a rig with a single mast located forward of 50% of the length of the sailplan. In this traditional definition a sloop could have multiple jibs. Cutters had a rig with a single mast located 50% of the length of the sailplan or further aft, multiple headsails and reefing bowsprit. Somewhere in the 1950''s or 1960''s there was a shift in these definitions such that a sloop only flew one headsail and a cutter had multiple headsails and mast position became irrelevant. For the sake of this discussion I assume we are discussing the modern definition of a sloop and a cutter.
Historically, when sail handling hardware was primitive and sails were far more stretchy than they are today, the smaller headsails and mainsail of a traditional cutter were easier to handle and with less sail stretch, allowed earlier cutters to be more weatherly (sail closer to the wind) than the sloops of the day. With the invention of lower stretch sailcloth and geared winches, cutters quickly lost their earlier advantage.
Today sloops are generally closer winded and easier to handle. Their smaller jibs and larger mainsail sailplan are easier to power up and down. Without a jibstay to drag the Genoa across, sloops are generally easier to tack. With less hardware sloops are less expensive to build.
Sloops come in a couple varieties, masthead and fractional. In a masthead rig the forestay and jib originates at the masthead. In a fractional rig, the forestay originated some fraction of the mast height down from the masthead. Historically, sloops were traditionally fractionally rigged. Fractional rigs tend to give the most drive per square foot of sail area. Their smaller jibs are easier to tack and they reef down to a snug masthead rig. Today they are often proportioned so that they do not need overlapping headsails, making them even easier to sail. One of the major advantages of a fractional rigs is the ability when combined with a flexible mast, is the ability to use the backstay to control mast bend. Increasing backstay tension does a lot of things on a fractional rig: it tensions the forestay flattening the jib, and induces mast bend, which flattens the mainsail and opens the leech of the sail. This allows quick depowering as the wind increases and allows a fractional rig to sail in a wider wind speed range than masthead rig without reefing, although arguably requiring a bit more sail trimming skills.
While fractional rigs used to require running backstays, better materials and design approaches have pretty much eliminated the need for running backstays. That said, fractional rigs intended for offshore use, will often have running backstays that are only rigged in heavy weather once the mainsail has been reefed. The geometry of these running backstays typically allow the boat to be tacked without tacking the running backstays.
Masthead rigs came into popularity in the 1950''s primarily in response to racing rating rules that under-penalized jibs and spinnakers and so promoted bigger headsails. Masthead sloops tend to be simpler rigs to build and adjust. They tend to be more dependent on large headsails and so are a little harder to tack and so require a larger headsail inventory if performance is important. Mast bend is harder to control and so bigger masthead rigs will often have a babystay that can be tensioned to induce mast bend in the same way as a fractional rig does. Dragging a Genoa over the babystay makes tacking a bit more difficult and slower. While roller furling allows a wider wind range for a given Genoa, there is a real limit (typically cited 10% to 15%) to how much a Genoa can be roller furled and still maintain a safely flat shape.
Cutters, which had pretty much dropped out of popularity during a period from the end of WWII until the early 1970''s, came back into popularity with a vengeance in the early 1970''s as an offshore cruising rig. In theory, the multiple jibs allow the forestaysail to be dropped or completely furled, and when combined with a reefed mainsail and the full staysail, results in a very compact heavy weather rig (similar to the proportions of a fractional rigged sloop with a reef in the mainsail). As a result the cutter rig is often cited as the ideal offshore rig. Like fractional rigs, cutter rigs intended for offshore use, will often have running backstays that are only rigged in heavy weather once the mainsail has been reefed. Unlike the fractional rig, the geometry of these running backstays typically requires that the running backstays be tacked whenever the boat is tacked.
Cutters make a less successful rig for coastal sailing. Generally cutters tend to have snug rigs that depend on larger Genoas for light air performance. Tacking these large Genoas through the narrow slot between the Jibstay and Forestay is a much harder operation than tacking a sloop. As a result many of today''s cutters have a removable jibstay that can be rigged in heavier winds. This somewhat reduces the advantage of a cutter rig (i.e. having a permanently rigged and ready to fly small, heavy weather jib).
Cutters these days generally do not point as close to the wind as similar sized sloops. Because of the need to keep the slots of two headsails open enough to permit good airflow, headsails cannot be pulled in as far as on a sloop without stalling out the slot. Since cutter rigs are generally associated with the less efficient underbodies that are typical of offshore boats, this is less of a problem that it might sound. Cutters also give away some performance on deep broad reaches and when heading downwind because the Genoa acts in the bad air of the staysail.
|04-29-2002 03:15 AM|
Cutter rig vs. sloop rig
While we wait for the real experts to reply, I can tell you what little I know: cutters are generally thought to offer more options for balancing your sailplan. Having, for example, a genoa on a headstay furler, and a smaller staysail (some prefer hanked-on over a furler), you can quickly quickly furl the genny and get the staysail into action in a blow. The staysail is closer to the mast, moving the center of effort closer to the midpoint of the boat, as well as lower.
Some claim that tacking a large headsail around the forestay can be a problem, but there are designs for temporarily repositioning the forestay when you are using just the headstay and genoa.
I believe that a cutter''s best point of sail is reaching. With the wind from close to broad reach, the extra sail can offer a lot of drive. While beating and running, the staysail is said to offer little to the sailplan. Of course, there are exceptions to this, too. I have seen some boats with two poles running the headsail and staysail "wing and wing."
|04-28-2002 08:30 PM|
Cutter rig vs. sloop rig
We are very new to sailing and have a few questions. What are the pro''s and con''s of a cutter rig vs. a sloop rig?