SailNet Community - Reply to Topic

   Search Sailnet:

 forums  store  


Quick Menu
Forums           
Articles          
Galleries        
Boat Reviews  
Classifieds     
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Charts
Clothing
Electrical
Electronics
Engine
Hatches and Portlights
Interior And Galley
Maintenance
Marine Electronics
Navigation
Other Items
Plumbing and Pumps
Rigging
Safety
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here






Go Back   SailNet Community > On Board > Gear & Maintenance > Resheaving Main Halyard
 Not a Member? 


Thread: Resheaving Main Halyard Reply to Thread
Title:
  

By choosing to post the reply below you agree to the rules you agreed to when joining Sailnet.
Click Here to view those rules.

Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Topic Review (Newest First)
07-16-2001 05:15 PM
scottcallahan
Resheaving Main Halyard

oh well i guess i was too late
07-16-2001 05:13 PM
scottcallahan
Resheaving Main Halyard

i would use hi test twine and put a teardrop sinker on the end and just toss the sinker over the shiv let it drop down the mast. tie the sheet to the end WITHOUT the sinker on it . then tape up the joint so that it does not snag. then fish out the weight from the bottom and start pulling slowly and gently.
07-02-2001 07:54 AM
Leon-T
Resheaving Main Halyard

We crimped a lead weight onto fishing line, then whipped the fishing line onto a messenger line at 3 places (due to the slippery nature of the fishing line). We then sewed the other end of the messenger line onto the halyard, and sent everything down. Worked like a champ.
06-23-2001 07:58 PM
Headman
Resheaving Main Halyard

Leon-T
Well, did it work?
Tom S.
06-21-2001 10:24 AM
Leon-T
Resheaving Main Halyard

Thanks, Tom. I really didn''t want to unstep the mast.

One variation I think I''ll try: instead of taping the halyard to the fishing line, you can get a more secure connection by using a leader clip at the other end of the fishing line to connect to a sewn loop in the main halyard. You can then drop the fishing line down and pull the main halyard up without tape or soap (I think soap would be messy from the bosun chair).

Thanks again.
06-20-2001 12:32 PM
Headman
Resheaving Main Halyard

Something else you might try before lowering the mast is a round lead weight on some fishing line. Drop it down and pull the line up. Lean the boat to the side where the halyard exits, and pull all other halyards taunt. When you tape the new halyard to the fishing line, taper it out quite a ways and lubricate the tape with dish soap. This works nine out of ten times.
Tom S.
06-19-2001 10:26 AM
JeffH
Resheaving Main Halyard

I depending on the boat, on a 26 footer is probably easier to lower the mast to the ground and remove the mast base plate and then use a pvc pipe to feed the line. You can 1/2" and 3/4" diam. PVC piping for next to nothing and it is very easy push a messenger line ip the mast. I like using PVC since it is easy to screw the connections togther and be able to store the pusher for future use. Before you feed the tube in make sure you the other internal halyards are pulled tight and in thier normal positions. Position the mast with the right part of the mast facing down so that the tube passes through the mast exactly where you want it with a clean lead past spreaders and other obstructions.

There are a number or ways to pull the halyard through but the easiest is to put a looped pig tail of 1/8" line on the end of the pipe so that you can hook that with a hanger and pull it out of the mast. Stitch the end of the halyard on the pigtail and pill it down through the mast. Stop when you get to the exit box and fish the pigtail out. The other way is to tape a messenger line to the pipe and pull it to the top of teh mast and then fish it out.

Jeff
06-19-2001 06:53 AM
Leon-T
Resheaving Main Halyard

I need some suggestions on resheaving the main halyard down a mast of a 26 foot sloop.

Tried sewing a bicycle chain to the end of the halyard (to give it some weight) and sending the chain over the sheave at the masthead and into the mast, but the chain got stuck inside.

I''d like to make the next trip up the bosun''s chair my last (for a while). Thanks.

 
Posting Rules
You may post new threads
You may post replies
You may post attachments
You may edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On


All times are GMT -4. The time now is 05:44 PM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) Marine.com LLC 2000-2012

The SailNet.com store is owned and operated by a company independent of the SailNet.com forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.