SailNet Community - Reply to Topic

   Search Sailnet:

 forums  store  


Quick Menu
Forums           
Articles          
Galleries        
Boat Reviews  
Classifieds     
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Charts
Clothing
Electrical
Electronics
Engine
Hatches and Portlights
Interior And Galley
Maintenance
Marine Electronics
Navigation
Other Items
Plumbing and Pumps
Rigging
Safety
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here






Go Back   SailNet Community > On Board > Gear & Maintenance > striping tape?
 Not a Member? 


Thread: striping tape? Reply to Thread
Title:
  

By choosing to post the reply below you agree to the rules you agreed to when joining Sailnet.
Click Here to view those rules.

Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Topic Review (Newest First)
05-08-2010 04:49 PM
capttb A little dish detergent in the water reduces surface tension and acts as a lubricant for a few seconds more "working time" and the squeegee slides a little smoother. However, having never done it without the soap I guess I can't say for sure.
That's how someone taught me to do it ages ago and since it worked I never thought to question it.
BTW your stripe looks excellent.
05-06-2010 11:50 PM
Bene505
Quote:
Originally Posted by capttb View Post
In general, striping tape is a vinyl based general purpose material in that it is used for cars, boats, signs etc. Various manufacturers including 3M, I have some now from a company called Lilly. It comes in 150' rolls at about $75 US if I remember right. The hardest part of the job is removing the old tape, and it must be removed, I use a warm sunny day, heat gun, and new (fresh edged) disposable plastic putty knives. Start lifting the tape at a corner, you want it just warm enough to pull the tape off slow and gentle. Too fast or cold it snaps and you start over, too warm it melts or just comes apart. Then clean the remaining adhesive off with a solvent, denatured alcohol works.
You put the new tape on with a small squeigee (? you know what I mean) and a squirt bottle with slightly soapy water. The tape in first picture looks too light because it still has the backing tape on which you remove after it dries.
I've never had a problem with it coming off, and seems to last as long as paint in the sun.

What is the soapy water for?

Regards,
Brad
04-15-2010 12:18 PM
SVCarolena
Quote:
Originally Posted by gershel View Post
What's the trick for geting a a smooth curve? I replaced my 2" stripe a few years ago, and as careful as I tried to be, I still got some slight waves.
Marc
Doing the longest sections possible as you work along. I used to do car pinstripes years ago and there is a learning curve. I never used the soapy water method for stripes, but did when I put on our hull lettering and it would probably make it easier for someone new to the process.

As for my technique, it is hard to describe, but I basically stick down one end, wherever you want to start. I then keep the tape taught, being careful not to over stretch, and pull the backing paper for a good length (for me, probably six to seven feet at a time). Then, keeping the tape away from the hull (you don't want it to stick until you are ready), sight down the length of the material until it follows the lines you want. Then, slowly bring it to the hull for initial contact. To follow the hull lines, you will need to raise/lower the tape as it is coming in contact with the hull. The longer the lead section you work with, the straighter your lines, and it will better allow for graceful curves along the hull. I keep pulling the backing tape as I move along, so that there is always several feet of tape ready to stick. When you get to the end, stick it down longer than the point you want to stop, then trim with a fresh razorblade.

I hope this makes sense (much easier to show in person than to write-up.).
04-14-2010 10:16 PM
southshoreS24 looks pro to me!
04-14-2010 09:11 PM
MarkCK Here is the finished project. I found 80 foot of tape at a local autographics place. It didnt turn out too bad, not exactly professional looking, but not too bad. I had my first sail of the season today.
03-14-2010 02:01 PM
Matto It hasn't come in yet so I haven't paid for it but I seem to recall the shop saying it would be around 60 bucks. That's for a 150ft roll of 1in wide tape.
03-13-2010 10:58 PM
bljones take your time, and on relatively straight sections work on spaces as wide as your arm span. lay the tape out, gently press it down, step back to make sure it is straight before you burnish it. if you have a cruve to work with, lay down a guide edge using masking tape first. cut the masking tape as need to provide a guide line that follws the curve you want, then lay out your tape with an edge of the tape butting up against your masking tape guide. if you have to cut your stripe tape to allow the necessary relief to follow the curve, use a SHARP razor blade or olfa cutter, then overlap pieces and trim back the overlap. This is the really big advantage of tape over paint. If you screw up you can simply pull it off and start again.
03-13-2010 10:45 PM
gershel What's the trick for geting a a smooth curve? I replaced my 2" stripe a few years ago, and as careful as I tried to be, I still got some slight waves.
Marc
03-13-2010 08:54 PM
MarkCK The 3m scotchal is on my short list of what I am going to buy. Can I ask what the auto shop charged for the roll?
03-13-2010 03:41 PM
Matto I've ordered myself a 150' roll of 3M scotchcal striping tape from a local automotive detailing shop. According to 3M it's good for boats, anyone here have experience otherwise?
This thread has more than 10 replies. Click here to review the whole thread.

 
Posting Rules
You may post new threads
You may post replies
You may post attachments
You may edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On


All times are GMT -4. The time now is 11:16 PM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) Marine.com LLC 2000-2012

The SailNet.com store is owned and operated by a company independent of the SailNet.com forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.