SailNet Community - Reply to Topic

   Search Sailnet:

 forums  store  


Quick Menu
Forums           
Articles          
Galleries        
Boat Reviews  
Classifieds     
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Charts
Clothing
Electrical
Electronics
Engine
Hatches and Portlights
Interior And Galley
Maintenance
Marine Electronics
Navigation
Other Items
Plumbing and Pumps
Rigging
Safety
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here






Go Back   SailNet Community > On Board > Gear & Maintenance > Painting small aluminum parts
 Not a Member? 


Thread: Painting small aluminum parts Reply to Thread
Title:
  

By choosing to post the reply below you agree to the rules you agreed to when joining Sailnet.
Click Here to view those rules.

Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Topic Review (Newest First)
04-07-2010 11:52 AM
jrd22 I had to paint some parts I made out of aluminum and got a zinc primer and top coat in spray cans from an auto paint place. I also used a clear coat for protection but you wouldn't need to. The key is to use the right primer on aluminum and the paint store had it on the shelf. The cans were much more expensive than Rust Oleum but have held up for almost three years now and still look new.
04-07-2010 10:51 AM
cghubbell I suspected it would, and I'm greatly relieved to hear that it works, especially that it worked in a salt environment which I suspect is more harsh.

The wait time for curing is no problem. My launch date isn't until May 17th, and I still need to glass in the deck I'm re-coring. Plenty to keep me busy before they get splashed!
04-07-2010 10:01 AM
tommays I spent a ton OF money paainting my mast white and it was well worth it

BUT i had to do the ends of the boom in black and i was NOT droping the bucks for a quart of it

SO i went with spray can rustolem primer and paint and it has held up FINE after ONE year in saltwater

You do need to give at least a WEEK to compleatly dry
04-07-2010 09:54 AM
cghubbell
Painting small aluminum parts

I have a set of aluminum stanchion bases that have done a great job of slowly corroding since their inception in 1977. A few hours with the new Dremel tool, and I was able to clean them off nicely. However, I'd like to protect them so I don't need to do this again for a long time. My thought was that since the boat's aluminum toe rails are black, I'd paint the stanchion bases the same flat black. That brings me to my question...

I've seen all kinds of advice for priming and painting aluminum spars, or hulls. The products I see recommended tend to come in quantities that are WAY too much for this little job. I only need about a pint of paint. My stanchion bases also don't take a lot impact abuse, so I'm thinking (hoping?) there may be a more economical yet still effective way to prime and paint them without buying a gallon of something expensive.

My boat is fiberglass, used 100% in fresh water (Lake Ontario), and I'm a weekends-only cruiser (so far!). So, again, I think my demands are less than some of the hull / spar oriented products are designed for. No ocean crossings in my current plans, and I'm not planning to paint any other aluminum in black, so no other places to leverage the purchase.

Has anyone used a Krylon or Rustoleum (or other more widely available paint?) product for small parts like this with any success? Yikes, I hope I won't be flogged for suggesting a non-marine paint My refit budget is hurting, so I'd prefer throw money where it's not justified. Then again, if I gotta do it, I will. Any thoughts?

Thanks,
Chris

 
Posting Rules
You may post new threads
You may post replies
You may post attachments
You may edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On


All times are GMT -4. The time now is 02:13 PM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) Marine.com LLC 2000-2012

The SailNet.com store is owned and operated by a company independent of the SailNet.com forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.