|Topic Review (Newest First)|
|04-21-2010 11:24 AM|
Originally Posted by zz4gta View Post
|04-21-2010 11:22 AM|
Originally Posted by wunhunglo View Post
I found this out near the end of last season when I decided to buy some sails and the sail maker came out to measure. He had worked on another Scampi in CT and notided the difference right away.
Last season, I had tremendous trouble keeping the boat flat. The sails were old, so I'm sure that didn't help, but even after the new sails came there was an issue. The sail maker and I suspect it is sue to the extra high rig.
Its very possible it was made this way. The mast step looks to be original, although a new spar could have been made to fit it at some point. I'll probably never know. Even if it was original, I'll never know if the keep was changed to help offset the taller rig.
|04-21-2010 02:46 AM|
Hm, I thought I replied to this but I now can't find the reply...
Someone on another forum suggested I do it the way that the J80 handles it. There was a picture of an interesting cam cleat with a riser. The halyard came out of the mast and down through the riser. When the halyard is pulled down and away from the mast the halyear goes through the cam cleat. When the halyard is pulled straight down it comes out of the cam cleat.
So I guess it could be uncleated from the foredeck or from the pit if the halyard is run down through a block at the mast step and then aft...
This solves the issue of having to be able to reach a clutch to open it or any other cleat to uncleat. So now a short foredeck person can do the job if the halyard exits the mast at about 7 feet up.
|04-20-2010 11:18 PM|
Why can I not find the schaefer halyard stoppers at their website. I was hoping to find a better picture as to how said stopper was mounted. I could see using this on my boat, to aid when sailing with spouse, with myself forward at the mast letting things down slower than my foot dragging the line, then again this may NOT be what I want/need either.........
|04-20-2010 09:34 PM|
On my 30 footer we use a cam cleat a Harken 150 on our spin halyard, to me a clutch is too complicated.
I would also suggest getting rid of your pole topping lift and using your spare jib halyard instead. Saves weight and complexity.
|04-20-2010 01:49 PM|
I've seen cam cleats also used to hold the halyard up. A clutch is too big and too much work to open. On a 30 footer, a mast man would be a good idea if you have extra crew. On my 25' a mast man would just get in the way.
Make the spin exit on the starboard side if you normally do port roundings. Keeps the 'jumper' on the high side.
|04-20-2010 10:36 AM|
I agree with Faster. Halyard stoppers particularly on the spin halyard, make life a lot easier for foredeck and pit.
Here's some Schaeffer stoppers that would be OK for a Scampi. BTW: You have a great boat in the Scampi IOR half Ton. One of Peter Norlin's best. Excellent in heavy air. Does yours now have a taller rig than the original design?
I would put the stopper at a height as high as you can so that the mast crew almost has to jump or stretch to reach it. Any lower and it makes it awkward to put body weight into to "jumping" the halyard.
Re: halyard exits: given the reasonably easily handled size of the rig on a Scampi, except for the spinnaker halyard exits, I wouldn't cut any more exits in the mast. The genoa and main halyard should be easily handled by the pit crew on a hoist, and there's often not as urgent a need to hoist as fast as possible as much as there is on a chute. i.e. if doing a headsail change, it's not critical to take 10 seconds longer hoisting compared with a chute where 10 seconds might have it filling before it's up.
|04-20-2010 10:25 AM|
I would think a foot apart, staggered fore-and-aft with 2 per side would be plenty. Place only one exit at any given height in the mast.... but I'm not a rigger so it would be best to consult an expert.
On our boat they are closer together than that with no apparent issues.
|04-20-2010 09:47 AM|
Originally Posted by Faster View Post
How far should the openings be staggered to keep the mast strong?
|04-19-2010 07:51 PM|
I'd argue that even the main halyard could/should be set up that way... much easier to hoist, esp if couple cruising, if one person can jump it at the mast.
They can't all be the same height, of course, you'll need to stagger them to avoid excessively weakening the spar, but between 5 and 7 feet up should allow most crew to get a pretty good jump.
Here's another idea: for the spinn halyard, run it through a mast-mounted clutch - then the mast man or even the foredeck crew can hoist it by jumping it, the clutch holds it while the pole gets properly set etc. When you have some time, pull the tail through to the normal cockpit-located stopper so it can be released from the cockpit on the douse. (don't forget to open the mast-mounted clutch, though!!)
|This thread has more than 10 replies. Click here to review the whole thread.|