|Topic Review (Newest First)|
|05-12-2010 09:51 PM|
|sailingdog||Looking pretty good there EMK.|
|05-12-2010 03:10 PM|
|eMKay||Actually I rolled the stripes, instead of tipping I just kept rolling until the bubbles were gone, then it leveled out nicely. I started tipping but like the first time it wasn't working. So I tried to roll over the brush marks, and the marks went away and so did the bubbles. Just used blue painters tape for the lines. They aren't perfect.|
|05-12-2010 02:32 PM|
|bljones||What brush and tape did you use for the boot stripe, EmKay?|
|05-12-2010 02:28 PM|
Originally Posted by cb32863 View Post
|05-12-2010 01:59 PM|
|cb32863||Looking really nice eMKay, really nice. Not sure if anyone is ever fully satisfied when they do the work themselves.....|
|05-12-2010 01:47 PM|
Boot stripes painted, still need to do the cove stripe, I'm doing that in vinyl but the stuff I bought was too fat...
|05-10-2010 11:52 AM|
|eMKay||Yeah this stuff seems pretty forgiving, and I can buff and wax it unlike 2 part. It was actually 40-45 degrees when I started. What I did was thin a little, spray, wait 30 seconds to see what it would do, then thin a little more. Did this three times on my test piece, then sprayed the boat. I could have waited until better weather next week, but I want to let it cure a bit before it goes in the water, trying to get it in ASAP. I'd rather be sailing|
|05-10-2010 11:35 AM|
I would be happy with that and as cold as it is up there i am supprised you got such good results
Two part paint would have not been happy and it will be intresting to see how the one part holds up
|05-10-2010 11:30 AM|
Sand out the brush marks (sanded most of the paint off!), spray 2 coats, looks good, not great. I'm going to leave it alone for awhile (after putting stripes on of course) then wetsand and buff it either right before it goes in the water (couple weeks) or next year after the paint has a chance to cure.
|05-06-2010 11:17 PM|
Originally Posted by turban10 View Post
The roller type is important. Do not under any circumstances use a roller from the hardware store, not even for the primer. Redtree makes a good roller cover. It's an extremely thin foam roller that's also epoxy proof. This roller will allow you to apply the correct amount of paint, which isn't much.
The brush is extremely important too. Most paint manufacturers recommend a badger hair or similar brush to tip the paint. One of these brushes will set you back about 25 bucks. I didn't like the finish I was getting with my badger hair brush, so I went shopping. I found a set of paint brushes in the oil painting section of the local hobby store (hobby lobby) right next to Mr. Happy trees. They were a cheap "chip" brush, but the bristles were a very fine, soft nylon. These brushes were awesome. Almost no brush marks immediately after tipping, and those marks laid down about 5 minutes later. The best part was that these brushes come in a 3 pack for 3 dollars. I only used the 3" brush, and threw all of them away after each uses. The thinner to clean them would cost more than another 3 pack.
The roll and tip process itself is best done with 2 people. I had 3 people on hand when I painted because I was able to use a rolling scaffold. My friend would roll, I would tip, and whoever else we could get would drive the scaffold.
One of the first tricks you have to perfect is getting exactly the right amount of paint on with the roller. Too little and the brush will drag and leave ugly "chatter" streaks. Too much and the paint will run, and I'm not talking very much too much.
Roll the paint on, being careful to get the right amount of paint on. Then follow immediately behind with a dry brush to knock the roller stipple down. The brush should glide smoothly on the surface. If it doesn't, you could have too little paint, or the paint may need to be thinned a little. The brush should be held at about a 45 degree angle and make vertical strokes from top to bottom. I masked off the bottom of the boat with heavy masking paper. At the bottom of each brush stroke I wiped the brush on the paper to remove excess paint. If I didn't, the paint would run under the rub rail. If you make a mistake, or have a run, or anything else, DON'T GO BACK AND FIX IT. Odds are you'll make your mistakes in the first coat or two, and you'll be sanding anyway. Even if you make a mistake in the final coat, don't fix it. It won't look that bad after it dries, and you won't see it with the boat in the slip.
|This thread has more than 10 replies. Click here to review the whole thread.|