|Topic Review (Newest First)|
|05-09-2010 09:22 PM|
A friend got one of the units you mentioned, not sure which model but apparently one is "non-standard POE" and can actually run from 12VDC. My 3220 is true POE with a third-party 12-to48V converter. I'm happy with mine, works well and provides WiFi coverage for iPods and such all over the boat in many anchorages.
Yes, boat projects tend to experience scope creep. This spring's projects were to upgrade my transom shower to hot/cold, and rewire my AC entry (to put the breaker before the inverter/charger and remove excess wire), which involved emptying the cockpit floor liferaft locker and removing some panels.
Now, I find myself refinishing, epoxying and redrilling screw holes, and repainting those panels and a few more. None of which was on my pre-launch list.
|05-09-2010 06:34 PM|
|rljend||I see the 3220 is now a discontinued product. My antenna upgrade is questionable - when the tide is out, the boat frequently drops the connection, so now I'm considering the EOC 2610/1650 or purchasing a repeater. Any thoughts? I'm trying to leave the first of next month and hadn't expected this to turn into a major project, but then again, that's typical for just about all boat work. Tomorrow I'll call my isp to see if they have problems with me port forwarding #25, since I can't get the email set up to pass a test.|
|05-08-2010 09:58 PM|
I have a few photos, will try posting them. There isn't much to my "installation" as the forward camera is sitting on my zodiac which is inverted on the forward deck, and the aft camera is on its bracket which is wedged between two of the stoppers next to the companionway. Each cam's power cord runs under the nearest hatch, with the wall-wart inside.
Range is not an issue as I have an Engenius EOC-3220 WiFi box on the stern arch set up as an AP and WDS repeater from the main marina AP across the road, so the cameras only have to reach ten or thirty feet. The boat's AP covers the 600-800 feet to the office, which is sometimes marginal because of a large metal-covered hangar in right between. Last year I was much farther back in the yard and it worked as well or better.
I saw the domes (from Hong Kong) before; there are many like that designed for fixed-mount cameras. Domes for pan/tilt tend to be much much larger. I don't know the model of the one I have, the clear dome portion is about 8" diam which is overkill but all I could find. It may be too big&ugly to mount on the arch, but maybe up the mast it will be less noticeable. I took a chance for $80 at a surplus/electronics/alarm shop in Montreal.
A friend sent me these links for the Airlink cameras, I've found several to be very useful, especially the still image links for my iPod Touch and Blackberry, neither of which did much with the live video.
Techplay | Airlink SkyIPCam Foolery
Airlink101 SkyIPCam 747W - Working : ZoneMinder
You can also use the syntax
to quickly pull up the image without extra clicks or typing (but not on IE, they removed that feature in the name of security).
I should mention that I have a couple of port-forwarding rules on the main marina AP (I installed their system, so I have full config access), to reach my cameras (and NMEA server, and VOIP TA) through their firewall. Whether they work anywhere else is hit-or-miss, but generally if the baot isn't at my dock, it's because I'm aboard.
...spent the last few days rewiring my AC entry instead of playing with the cameras... at least the cameras are accessible.
|05-08-2010 09:30 AM|
Originally Posted by Bene505 View Post
Camera's web site - Internet Cameras – AICN777W
You'll need this - DynDNS.com Dynamic DNS: Free DDNS Service
|05-08-2010 09:21 AM|
Originally Posted by redline View Post
Let us know how the dome works out and where you found it. The link Brad included looked helpful, but they seemed too small for the 777w from my quick look.
What kind of range were you getting to your router? I had reception problems until I installed a higher gain antenna on the camera, so now I have a very good response from the 60' from dock to router.
|05-06-2010 01:10 PM|
Can you post some pictures of your set-up? Maybe some links to what you used? I'm very interested in this too. (I bet a lot of people on here are as well.)
Show off your work!
Edit: Here's a housing 4" Waterproof Outdoor Dome Network Cam Shell Housing NW - eBay (item 390192135923 end time May-06-10 19:43:37 PDT)
|05-06-2010 10:03 AM|
The 777 camera is powered with a 12V wall-wart so I would not expect a problem using an inverter; I have run mine briefly on my Xantrex Freedom25 inverter/charger. If you had any issues you could easily substitute a different power supply.
Depending how far your porch is from the boat; be aware these are not stunningly high-resolution cameras. The "3X zoom" feature give a pretty blocky view. The quality is ok for the length of the boat, but I did use two, one on the foredeck and another at the cabin entry (I wanted more detail of the winter cover over the cockpit area). Bright light does cause some flare. You'll be able to see that the boat is still afloat, certainly. ;-)
I just picked up a "dummy" security camera with dome (the camera is dummy, the dome is real) to see where I might mount it outside more permanently; possibly hanging it under the (future) radar scanner.
|05-06-2010 08:16 AM|
I've also thought about using a weather proof housing, but since the boat is close to the house, I'll probably just install a camera inside the patio for overall monitoring. I haven't received the cameras yet, but I reviewed the online documentation and seem to remember a warning about exterior installations. Apparently, a bright light source (lightning?) can damage the picture quality.
I'm not too concerned about dead batteries, but a 110 outage is a definite possibility. Do you see any problems powering the cameras through an inverter.
|05-03-2010 10:58 AM|
I have not played with the GPIO (yet), but based on the manual, you could connect a (fused) 12V source through a float switch to the GPIO In+ terminal and In- to ground. Then you would configure the Event Config / GPIO Trigger to Send Email.
I think it would email you a still picture, but if that's the only situation in which it does send a picture, you'd know that the float switch closed, even if the camera is looking elsewhere. If it's the regular bilge pump switch (you might want to put some voltage spike protection on the input because of the motor) you'd get an email every time the pump cycles. If you install a second dedicated switch just a little higher than the bilge pump switch, you'll get a notification email only if the water rises above the pump's cut-in; a sign of some problem.
Of course, if the problem is that the bilge pump is not running because the batteries are dead, the camera may not be running either, but that's a different issue (there are commercial vessel-monitoring products out there which would deal with that).
You're tempting me to do something similar when my winter cover comes down next weekend and I have to move the cameras inside. One thing - please let me know if you find a small weatherproof housing that fits these cameras. Most Pan/Tilt camera domes are huge (not to mention expensive).
|05-02-2010 01:02 PM|
Just the information I was looking for! Thanks.
I noticed that the 777w has GPIO, but not sure how I'd hook it up to a bilge switch, so I'm considering the 500w for bilge monitoring and the 777w for overall exterior monitoring.
|This thread has more than 10 replies. Click here to review the whole thread.|