SailNet Community - Reply to Topic
Thread: Drill through guard or pedestal? Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.

User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

  Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below

  Topic Review (Newest First)
05-20-2010 02:56 PM
chef2sail I installed all of our chartplotter and autopilot cables up throught the pedestal gaurd. Used a bolt with fishing line to fish the line up through the tubes and out the drilled hole. Gromet on the drilled hole. Do not forget to put rubber on the lower edges of gaurd tubes so their is no chafe when the line enters from the engine area into the pedestal gaurd. Also secure the cables so they do not swing or pull once installed.

05-18-2010 10:18 PM
scraph I'd pass it through the rail as mentioned above through something as simple as a grommet. I, personally, would not get too bent out of shape about "weatherproofing" the penetration. Ensure, if your decks are cored, that the hole you make in the deck at the base of the rail is sealed from the core. However ... I wouldn't make the (ineffective) mess of installing a grommet with sealant. It's not going to work very well in this location ... simply due to the combined difficulties of the curved sealing surfaces and potential for relative motion of wire in grommet or grommet in rail if you ever bump the cable.

Any amount of water entry through this penetration would collect harmlessly in the rail foot and if it does happen to drip into the boat ... would be so minimal you might as well call it humidity. It's not going to sink your boat if you don't get a cable penetration through a pedestal rail absolutely waterproof.
05-18-2010 09:50 PM
Pub911 As you refer indirectly above, be careful to keep the wire away from moving parts inside the pedestal...chains, cables, etc.

That said, I considered the same but found it more attractive to run up inside a guard tube then enter the instrument box without ever exposing the cable - a cleaner look and I think safer from abraision and weather. I 'hogged out' the SS tube right where the navpod box attaches and passed the AP cable into the navpod at that point. No unsightly wires.

Good luck.
05-18-2010 03:12 PM
eherlihy Any time that a wire will be installed through any thing you should use chafe protection. That is the only function of the grommet. This would apply to passing the wire / cable through either your pedestal, or the pedestal guard.

If you are concerned about waterproofing, get one of these;

or these;

or these;

BTW - these are called Deck Glands
05-18-2010 02:12 PM
btrayfors Weatherproofing isn't a problem. The grommets are good for chafe guard. Just coat the wire and grommet with a marine sealant for additional protection.

I'd be a bit concerned about passing autopilot wires thru the pedestal if they're anywhere near your compass. As you know, any current passing thru a wire creates an electromagnetic field around the wire; the strength of that field -- and the potential for mischief -- depends on several factors. You might run a test...if that's practical...before finalizing the installation.

05-18-2010 01:17 PM
Drill through guard or pedestal?

Couple of questions as I don't like drilling holes in boats.
  1. I need to run a cable for an X-5 Autopilot drive. I have good access from below decks up inside the pedestal. I'd prefer to run it this way as it will result in a shorter length of exposed cable in the cockpit (vs. running it through the pedestal guard). I can secure the cable inside the pedestal so it wouldn't present a hazard to the steering system. Any other concerns about drilling a 1/4" hole in, or running cable up the pedestal vs. the guard? Am I risking getting water inside the pedestal or is it practical to make that pass through water tight?

  2. Any personal experience with grommets for weather tightness and to protect from abrasion against the drilled metal? Would something like this hold up above decks?

Rubber Grommet Assortment Kit

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

For the best viewing experience please update your browser to Google Chrome