SailNet Community - Reply to Topic

   Search Sailnet:

 forums  store  


Quick Menu
Forums           
Articles          
Galleries        
Boat Reviews  
Classifieds     
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Charts
Clothing
Electrical
Electronics
Engine
Hatches and Portlights
Interior And Galley
Maintenance
Marine Electronics
Navigation
Other Items
Plumbing and Pumps
Rigging
Safety
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here






Go Back   SailNet Community > On Board > Gear & Maintenance > the head pump is harder to pump
 Not a Member? 


Thread: the head pump is harder to pump Reply to Thread
Title:
  

By choosing to post the reply below you agree to the rules you agreed to when joining Sailnet.
Click Here to view those rules.

Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Topic Review (Newest First)
06-03-2010 10:28 AM
svHyLyte With all due respect for Vasiline advocates, the stuff will eventually damage the lips in the lip seal at the top of the pump. If the pump is becoming difficut the rod can be lubed with a non-petrolieum based lubricant, e.g. a silicon grease lube.

Frequently, stiffness in the pump is a combination of the stiffening of the O-ring around the edge of the piston coupled with build-up of scale in the discharge hose directly aft of the Joker-valve. Adding a lubricant to the bowel, pulling it into the cyclinder with one or two strokes and then leaving the piston in the up position over night will lube the cyclinder and allow the piston O-ring to recover somewhat. Peggy Hall, the gruru of Head Maintenance also suggests pumping a bowel of water thoroughly mixed with a product known as "Salt Away" through the lines and allowed to sit over night. One can also use a product known as "Ryd Lime" (biodegradable) in the same manner or, in extremis, a couple of bowels with a 5% mix of Muriatic Acid although that should only be allowed to sit for 20-30 minutes before being flush out with fresh water (Raritan suggests at least 10 gallons of fresh water).

We keep a squeeze bottle with a solution of water abd Salt Away in both heads and always add a few quirts to the last bit of water in the bowel once the heads have been pumped clear after use and both heads have remained free for several years at a time.

FWIW...
06-03-2010 09:22 AM
Cruisingdad I have found teh best thing for the rod is Pool grease. It works well and lasts quite a while. If you have a Wilcox, you can try to loosen the black plastic nut on top, but will probably cause it to leak a little. It is also very likely that the rubber ring on the piston is getting hard/swollen. This is very common as they age - especially on the cheaper toilets. You can prolong its life by adding oil... we use mineral oil. I guess we use about an 1/8 cup initial, then a light coating every week or so and certainly with every pumpout.

If that does not work, you may be due a replace or rebuild. Be aware that on the cheaper toilets the costs to replace the whole assembly usually runs only a few dollars more (relatively) than the rebuild kit and is a WHOLE LOT EASIER and with less mess.

Just some thoughts. Good luck with it.

Brian
06-03-2010 08:36 AM
JimsCAL Scale will build up when used in salt water. Try pumping some vinegar into the pump and let it sit overnight. Could also be time for a rebuild.
06-03-2010 12:22 AM
jackdale I put a little olive oil through the head occasionally.
06-03-2010 12:06 AM
JiffyLube I rebuilt our Groco pump once. An O-ring goes around the piston of the pump in the chamber, and if it's hard to pump then I would lube up the chamber the piston is in. This will allow the O-ring to slide much easier. Lube with anything that will not affect the rubber of the O-ring.
06-02-2010 10:09 PM
btrayfors Don't know which toilet you have, but a bit of Vaseline periodically on my PH-2 has worked well for over 20 years. Apply directly to the metal rod. :-)

Bill
06-02-2010 09:44 PM
ekenna
the head pump is harder to pump

My wife is complaining the head is harder to pump this year. She said last year the metal piece under the handle had grease on it but this year it does not. Is there some kind of lubricate to use? I did not want to useany old grease because I an heard it can be harmful to plastic/seals. What do you put on the metal rod that slides in and out as you pull the handle up and down.

 
Posting Rules
You may post new threads
You may post replies
You may post attachments
You may edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On


All times are GMT -4. The time now is 08:46 AM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) Marine.com LLC 2000-2012

The SailNet.com store is owned and operated by a company independent of the SailNet.com forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.