SailNet Community - Reply to Topic

   Search Sailnet:

 forums  store  


Quick Menu
Forums           
Articles          
Galleries        
Boat Reviews  
Classifieds     
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Charts
Clothing
Electrical
Electronics
Engine
Hatches and Portlights
Interior And Galley
Maintenance
Marine Electronics
Navigation
Other Items
Plumbing and Pumps
Rigging
Safety
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here






Go Back   SailNet Community > On Board > Gear & Maintenance > Engines > Diesel > Westerbeke 38B4 hard to start
 Not a Member? 

Diesel This is a forum dedicated to diesel engines and their applicable accessories.


Thread: Westerbeke 38B4 hard to start Reply to Thread
Title:
  

By choosing to post the reply below you agree to the rules you agreed to when joining Sailnet.
Click Here to view those rules.

Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Topic Review (Newest First)
06-22-2010 07:37 AM
Maine Sail
Quote:
Originally Posted by saildog1 View Post
On this motor you have to hold the glow plug while pushing the starter button. If you just push the starter button nothing happens because it gets the power off the glow plug botton. Crazy set up but my Universal 25XP was the same way. I'll check out the selenoid.

That is the correct operation for the start circuit but the solenoid may still not be engaging even with the glow plug button still operating correctly. It is also possible that you have another issue but the solenoid is 20 seconds to check out and rule out..
06-22-2010 07:11 AM
saildog1 On this motor you have to hold the glow plug while pushing the starter button. If you just push the starter button nothing happens because it gets the power off the glow plug botton. Crazy set up but my Universal 25XP was the same way. I'll check out the selenoid.
06-22-2010 05:58 AM
tytower I also dont know the motor.
There are glow plugs with elements that burn an element red hot and what I call heaters which are an encased element.
With encased element type I give them 8 seconds ,turn them off and crank the engine.
Mine are drawing 60 Amps on a 3 cylinder VM motor and the starter draws 80 Amps so its one or the other and I think this is common with diesels

Now I had the case that the engine did not start. I kept cranking and cranking and perhaps if the battery held out it might start. Throttle was tried at many start positions.
Once hot it started first time every time .

Solution- After pulling the engine and fuel distributor to pieces and checking everything it was as simple as replacing the needles and nozzles on the injectors. The fuel was dribbling in instead of spraying in.
06-21-2010 09:45 PM
Maine Sail Test your glow plug solenoid, these motors tend to eat them. I just replaced the fourth one on my engine in 3k hours use.
06-21-2010 07:35 PM
JimsCAL No first hand knowledge of the 38B4. My previous Universal/Kubota had glow plugs. Thirty seconds of preheating usually was plenty for a quick start in warm weather. I would release the glow plug switch before cranking however (to reduce current draw). My current Yanmar has no glowplugs. Manual says apply full throttle to start. Seems to work.
06-21-2010 03:33 PM
saildog1
Westerbeke 38B4 hard to start

My 38B4 takes 3-4 pushes of the starter before it will start. The procedure I do is hold the glow plug for 30 seconds, while holding glow plug push starter button and it turns over no problem but does not start. Usually on the third or fourth time it starts, even when it is warm.

I have replaced the glow plugs, which 2 were bad.

This motor you turn on the key and when you press the glow plug button the fuel pump starts. It is a no bleed system. The book also states to push the throttle to wide open.

I have owned the boat for 3 years now and things have not changed since I bought it.

Any ideas, I think it is a fuel problem but I don't know where to start.

 
Posting Rules
You may post new threads
You may post replies
You may post attachments
You may edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On


All times are GMT -4. The time now is 12:02 AM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) Marine.com LLC 2000-2012

The SailNet.com store is owned and operated by a company independent of the SailNet.com forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.