|Topic Review (Newest First)|
|04-08-2011 07:38 AM|
Originally Posted by jackytdunaway View Post
Take a look at : Packing-Shaft - e Marine Systems at "http://www.emarineinc.com/categories/Packing%252dShaft"
|04-08-2011 06:32 AM|
|tommays||It will drip way less for a MUCH longer time without the need for as much service and replacement|
|04-08-2011 12:39 AM|
Not trying to be a wise-a$$, but...
That stuff looks great, but if it is not going to be completely "drip free" what is the advantage? The bilge is still going to fill to the lowest level that the bilge pump can pump it out, about half an inch. Its just going to take a little longer to get there. Once its there though, you'll still have 1/2 inch of water in the bilge.
So I guess I'm missing the point.
|03-11-2011 11:03 AM|
Originally Posted by Maine Sail View Post
But I can't stop thinking that the product you recommend sounds awfully like a good quality condom.
|03-11-2011 07:08 AM|
You guys are spending more than you need to.
Hamilton Marine sells Duramax Ultra-X for 1.68 ft in 3/16" PACKING ULTRA-X 3/16" SOLD BY INCH OR LBS 420" 176152
And in 1/4" for $3.00 per ft PACKING ULTRA-X 3/16" SOLD BY INCH OR LBS 420" 176152
Gore GFO from eMarine is $9.63 per foot in 1/4"!!!
I am VERY impressed with both Gore GFO and Johnson Duramax Ultra-X. What I am not impressed with is the knock off product made by Western Pacific Trading and sold by West Marine while similar it is not braided the same nor is it the same make up as Ultra-X or GFO.
Duramax Ultra-X is what I now use 90% of the time. Hamilton Marine sells it for next to nothing. The folks at eMarine a giving you bad advice on "drip free". Ask them if they plan on buying you a new shaft after it is eaten by crevice corrosion? The drips do more than lubricate they allow clean oxygenated water into the shaft log which helps prevent shaft corrosion.
BTW this shaft was set to "drip free" not "drips less". This particular shaft cost over $1500.00 to replace.....
|03-11-2011 07:00 AM|
|jackytdunaway||Where can i get the Gore GFO? I am having a hard time finding it.|
|08-26-2010 12:55 AM|
Whether the stuffing box should drip with the shaft at rest is really dependent on a few factors: 1) Number of rings of packing; 2) Type of packing material; and 3) How much friction you consider acceptable.
With traditional flax packing material, you may need to allow some dripping when at rest to keep the flax sufficiently waterlogged to prevent the packing material at the inboard side from drying out and scoring the prop shaft. With the GFO packing, this is not as necessary, but the box should still drip a tiny bit when the propshaft is turning.
Checking the temperature of the stuffing box while the propshaft is turning is a good idea. It shouldn't be more than about 15-20˚ warmer than ambient temperature of the water. Anything greater than that, you're probably risking scoring of the propshaft.
With all packing materials, but more so with flax-based packing, you should allow the packing material to absorb water for a while before adjusting. The flax-based packing, IIRC, will swell a bit as it absorbs water and adjusting the box before it has done so will lead to an overtightened box that will score the shaft.
Originally Posted by Omatako View Post
|08-26-2010 12:12 AM|
Originally Posted by sailingdog View Post
I haven't heard of the GFO/GFU products, they sound good, I may try and get some. I still use the old waxy flax stuff.
|08-26-2010 12:04 AM|
Here is the best tutorial on stuffing box repacking (if you haven't seen it already): Re-Packing A Traditional Stuffing Box Photo Gallery by Compass Marine at pbase.com Check out his other 'how-to' articles as many are just as thorough.
The correct size might be 3/16", 1/4" or even 5/16". I doubt it is bigger then that but it depends mostly on the shaft diameter and stuffing box size.
For my 27' Tartan with a 1" shaft it was 1/4" that fit the most snug.
|08-25-2010 01:34 PM|
Thanks to ALL for their inputs. I am leaning towards the GFO packing. The link I provided above points to an out dated site where the "buy-now" link fails.
I read in other posts that e-marine sells GFO online. The site is eMarineSystems.com and select the menue item "Packing-Shaft".
The website has some useful info, in particular, a table of packing size for standard Buck Algonquin Bronze Packing Boxes. See this link:
EMarine Systems Packing Shaft
I also talked to them over the phone. They claim that GFO can be used dripless but warned about over tightening. They suggest adjusting from the lose side, tightening the gland nut until the dripping stops (as oppose to over tightening and easing the gland nut).
Even though, I will still let it drip a drop or two per minute (Just to be on the safe side).
|This thread has more than 10 replies. Click here to review the whole thread.|