SailNet Community - Reply to Topic

   Search Sailnet:

 forums  store  


Quick Menu
Forums           
Articles          
Galleries        
Boat Reviews  
Classifieds     
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Charts
Clothing
Electrical
Electronics
Engine
Hatches and Portlights
Interior And Galley
Maintenance
Marine Electronics
Navigation
Other Items
Plumbing and Pumps
Rigging
Safety
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here






Go Back   SailNet Community > On Board > Gear & Maintenance > Diesel exhaust- water?
 Not a Member? 


Thread: Diesel exhaust- water? Reply to Thread
Title:
  

By choosing to post the reply below you agree to the rules you agreed to when joining Sailnet.
Click Here to view those rules.

Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Topic Review (Newest First)
07-18-2007 06:19 AM
Blue Eagle
Quote:
Originally Posted by halekai36
Yes it's caled an infrared thermometer. Simply aim it at the thermostat housing, read it, and compare it to the temp gauge.

Below is a link to the one I own & use for lots more than just engine stuff. You can even shoot it overboard to know the water temp... I bought it a Napa Auto for $59.00!

Raytek MiniTemp MT-4 InfraRed Noncontact Thermometers - Test Equipment Depot
Here's an even easier way: remove them from the donkey and plonk them into a pan of boiling water. If the thermometer doesn't read 100 degrees Centigrade, it's duff.

Next, let the water cool: As you do so, monitor when the thermostat that you've also removed from the donk closes. Compare this temperature (read off the 2-buck Mercury thermometer you've bought earlier) that's quoted in the workshop manual for your weather conditions / ambient temperature range. If they're different, replace the thermostat!

BE
07-17-2007 10:43 PM
camaraderie Halekai...we've been using globe with excellent results for some years now in two different boats/engines and none of the problems you report. It seems that some swear by them and have no problems and others hate them and have had problems. Maybe it is the individual models and applications rather than a "global" (g) problem.
I guess since they are all cheap...it might be best to carry one standard and one globe spare.... Getting the performance of the globe if possible but being ready with an alternative if not.
07-17-2007 08:49 PM
Maine Sail
Quote:
Originally Posted by swanfrogg
Anyone knows how to test if a temperature sensor and the temperature switches in the thermostat housing are functioning correctly?
Thank you
Yes it's caled an infrared thermometer. Simply aim it at the thermostat housing, read it, and compare it to the temp gauge.

Below is a link to the one I own & use for lots more than just engine stuff. You can even shoot it overboard to know the water temp... I bought it a Napa Auto for $59.00!

Raytek MiniTemp MT-4 InfraRed Noncontact Thermometers - Test Equipment Depot
07-17-2007 08:38 PM
Maine Sail
Quote:
Originally Posted by camaraderie
There's no need to replace an impeller that often...especially if you buy the good ones (Globe - as I recall.) We consistently get hundreds of hours from our impellers. The real enemy of impellers is winter layups and lack of use (and of course...closed thru hulls!). Once a year is plenty of changing for most uses.
Cam,

Be very, very careful with the so called "better" Globe impellers. I have tried three, in two differnt boats and all three of them spun off the PLASTIC center hub. Yes the rubber never did fail but that's because it could not spin! IMHO Globe impellers are a problem waiting to happen! Use the stock impeller and make sure you're getting water flow and you'll be fine. I change mine each spring!
06-14-2006 01:16 PM
Faster MBesant, you probably have that right and were very fortunate not to have run any longer, I suspect that 15 - 20 minutes would be the limit unless you had a very large hotwater tank that was quite cold to start with.
Our last boat allowed us to isolate the water tank from the cooling cct, and I remember watching the temperature of a warm engine plummet when we put the water tank back in the circuit - which prompted us not to do that again, the thermal shock can't be good for anything.
06-14-2006 10:58 AM
MBesant For those concerned on how the engine could run 15-20 minutes and not overheat, I have a theory
The engine has a closed, fresh water-antifreeze cooled system. This is designed to transfer heat to the raw water and discharge the raw water through the exhaust. Closed system was full of coolant so probably temp gauge was accurate
But boat also has an engine heated hot water tank. I think that the drinking water in the hot water tank had sufficient capacity to aborb engine heat for 15 minutes and prevent overheating. Cooling system opened the thermostat at 175 and then held there as heat was transferred into the tank. Water in tank got warm, but not hot. If we had continued, I am sure all the problems suggested might have occured
Will know more this weekend
Marty
06-14-2006 04:58 AM
Omatako Sorry to sound contrary Sailingdog but any closed cooling system needs to shed heat and this can only be done through some form of heat exchanger. In an automobile, the heat exchanger is in the form of an air cooled radiator. In a boat it is done through a heat exchanger that has coolant on one side and raw water on the other. I have never seen any other form of cooling system and I've surely not seen any boat with an aircooled system.
If it needs raw water, it will splash out of the exhaust (unless the exhaust is underwater - rare).
I agree with previous thread that a closed system will allow quite extended running before causing damage (maybe not 20 minutes!) but this will definitely show on the temp guage (unless of course that's faulty as well). Another contributor to running longer will be if the hot water cylinder is also in the form of a heat exchanger, this will absorb quite a lot of heat energy depending on it's size as will a refrigerant heat exchanger. Lots of variables.
This is surely a strange one. If the fairer is going to be keel hauled, hold him down there long enough to put another strainer on.
I never allow my engine to run more than a minute without seeing water puffing out.
06-13-2006 07:49 PM
sailingdog
Quote:
Originally Posted by hellosailor
The hard part is, do you let the bottom get real foul BEFORE you keelhaul the guy who faired it over? Or just keelhaul him now, and do it slowly and repeatedly? Decisions, decisions....
I'd keelhaul both the PO and the guy who faired it over...repeatedly.
06-13-2006 05:06 PM
hellosailor "PO of boat had a professional bottom job during which they faired over the raw water intake. ...Who would have thought"
Yeah, who woulda thought. Just when you think you've heard of everything.
If this is an intercooled engine (raw water cools heat exchanger, engine is a closed loop) then in cool wx it would be possible to run it without any damage, as the heat exchanger side would be acting as a heat sink and it might do well enough for 20 minutes under no load.
Still worth checking the exhaust very carefully, and especially the impeller and pump in the raw water side to see if they've been damaged.

The hard part is, do you let the bottom get real foul BEFORE you keelhaul the guy who faired it over? Or just keelhaul him now, and do it slowly and repeatedly? Decisions, decisions....
06-13-2006 02:34 PM
DeepFrz Running an engine without sea water going to the exhaust will melt your exhaust system.

I agree with TrueBlue.

I think we been had...

Deep
This thread has more than 10 replies. Click here to review the whole thread.

 
Posting Rules
You may post new threads
You may post replies
You may post attachments
You may edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On


All times are GMT -4. The time now is 09:04 PM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) Marine.com LLC 2000-2012

The SailNet.com store is owned and operated by a company independent of the SailNet.com forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.