SailNet Community - Reply to Topic
Thread: Sabre 28 Chain Plates Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.

User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

  Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below

  Topic Review (Newest First)
06-25-2007 08:06 AM
Sailorcto I have a 1973 Sabre 28 (hull #68) that suffered a minor rigging failure due to a softened bulkhead at the starboard chainplate. Since this is an early Sabre 28, the chainplate at the deck does not have the stainless steel collar on exterior, therefore must be constantly sealed or it will leak. I was lucky in many ways, the deck core was not damanged, the rig stopped short of dismasting by the interior chainplate boltheads catching on the underside of the deck. I steadied the rig, removed the turnbuckles and chainplate. The area of softness was restricted to a 3"x6" section of the interior starboard bulkhead (3/4" teak plywood) where the original chainplate bolts are 'swiss cheesed' into a very tiny area (thankfully, no fiberglass repair or bulkhead removal or $$$$$). I cleaned the deck hole out thoroughly and checked it with a moisture meter. No moisture or softness, whew.

I cut out only the soft area and replaced it with a block of maple very tightly fitted, shaped like an equilateral triagle with the top cut off (widest part at the bottom so any upward pulling would transfer the load to the bulkhead where it belongs). Then I had four 8"x11" hexagon pieces cut from T316 stainless by a local metal fabrication shop, drilled the holes to distribute the load much better then sandwiched two of the four chainplates over top of the original chainplate--using only 3 of the original holes in the (old) chainplate spread furtherst apart. Note, I made teak spacers 3/16" thick in the shape of the hexagons with the middle cut out to fit the actual chainplate (about 2-1/4" wide). I drilled 5 more holes wide on the hexagon plates to push the load outward. I used the remaining two hexagon for the port side to match. I rebedded the deck hole at the chainplate and now keep a vigilant eye on it throughout the year.

I did spend a lot of time on this, but mostly grinding down the raised letters of the new chainplate bolts, then polishing the bolt heads and the hexagon plates to a mirror finish. If it fails this time, the deck will simply detach from the boat.

In total, it cost me less than $200 (most of that to the metal shop to cut the stainless hexagons) and a couple days of my time spent polishing. Hope this helps other Sabre owners in similar situations. I think I have pictures from a full article I wrote a few years back. FWIW, RigRite has those stainless steel collars for the chainplates and a retrofit kit to add forward lower shrouds.
07-07-2006 10:01 PM
Sabre 28 chainplates

Our 1981 Sabre 28, which we purchased in 2004, had the same problem. The previous owner repaired the bulkhead with fiberglass & epoxy but neglected to retab the bulkhead to the hull. Our 18 year old son, with the assistance of a mentor from Sabre (we live in Maine) retabbed the bulkhead and resurfaced it using 1/8" teak veneer. It's a lot of work (and a very expensive yard job, if you hire it out) but we are pleased with the end result. We had the deck and deckhouse completely stripped and repainted this past winter and rebedded EVERYTHING. Surprisingly, the only core damage we've found has been near the forward starboard porthole (which I repaired) and around the emergency steering access in the cockpit. If you're up to this kind of repair, you'll have a great boat. One option is to have a yard do the structural repair and pick away at the carpentry at your convenience.
06-26-2006 10:04 AM
Big job

If you have soft ply in the bulkheads at the chain plates this is indicitave of long standing leakage there. A proper repair is a major project and I would re evaluate the deal - you better be getting a substantial price break on this. And you'd best be very comfortable using tools, working with fibreglass, and wood.

It's do-able but its not for the faint of heart!
06-26-2006 05:19 AM
Bulkhead Replacement

A couple of Bulkhead replacement projects:
06-25-2006 12:40 PM
Sabre 28 Chain Plates

We are looking @ a Sabre 28 but notice that the interior plywood bulkhead is soft where the bolts attach thru the plywood bulkhead. Does anyone know how I would fix this if we purchased the boat?

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

For the best viewing experience please update your browser to Google Chrome