SailNet Community - Reply to Topic

   Search Sailnet:

 forums  store  


Quick Menu
Forums           
Articles          
Galleries        
Boat Reviews  
Classifieds     
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Charts
Clothing
Electrical
Electronics
Engine
Hatches and Portlights
Interior And Galley
Maintenance
Marine Electronics
Navigation
Other Items
Plumbing and Pumps
Rigging
Safety
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here






Go Back   SailNet Community > On Board > Gear & Maintenance > Foam density/Rudder repair
 Not a Member? 


Thread: Foam density/Rudder repair Reply to Thread
Title:
  

By choosing to post the reply below you agree to the rules you agreed to when joining Sailnet.
Click Here to view those rules.

Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Topic Review (Newest First)
11-05-2010 03:17 PM
hellosailor "I don't think i'll be able to get the garage or basement that warm! "
Can your rudder fit, mostly, into a metal trash can? If so, brace the rudder in the can, fill with hot water from your sink, use your imagination and find a way to heat up the trash can so the water stays warm. No need to heat up the whole room.
11-04-2010 10:37 PM
scottyt do a search on emkay he redid his hunter 27 rudder and took lots of pics.
11-04-2010 10:31 PM
niebur
Quote:
Originally Posted by mysticsailor View Post
The heaviest foam US composites has is 16 lb. I read on their web site that for optimum expansion of the foam, the temperature should be warm. They mentioned 80 degrees.I don't think i'll be able to get the garage or basement that warm! Any comments on temperature affecting your application?

thank you both for the pouring tips.
Yes, it was definitely the 16lb foam then.

And yes, it was definitely not 80 degrees. I did try to keep it warmish, maybe it was 70 degrees, dunno. The foam develops quite a bit of heat by itself.

I would not sweat the temperature but of course you wouldn't want to do it in a freezing unheated space either. The stuff has a high heat storage capacity, so even if the space where you do the pouring is not super-warm, if you keep it in a nice cosy room and only bring it out for the pour you should be fine.

Oh, one more tip, this one is important: Go to Home Depot, buy a paint stirrer for your power drill. You have about a minute time to mix each batch, no way you can do this with a wooden paddle or something. I got the one with the plastic vanes; after the foam had hardened on them, you can get it off easily and think about the next batch.

I did at least 10 batches for the rudder. You don't want to pour too much at once for two reasons: one is that the stuff hardens before it fills the volume, and two, because it develops a lot of heat. And there is no harm to have lots of batches (other than that it takes a bit more time): This stuff adheres WONDERFULLY to itself. As well as to anything else
11-04-2010 10:03 PM
donradclife Take it over to an elderly aunt's house--they usually have the heater cranked up to 80...
11-04-2010 08:20 PM
mysticsailor The heaviest foam US composites has is 16 lb. I read on their web site that for optimum expansion of the foam, the temperature should be warm. They mentioned 80 degrees.I don't think i'll be able to get the garage or basement that warm! Any comments on temperature affecting your application?

thank you both for the pouring tips.
11-04-2010 07:58 PM
niebur
Quote:
Originally Posted by mysticsailor View Post
I'll be working on repairing the rudder on my Sabre 30 this winter. I can't find any reference on which foam density to use (there is 2lb.,4lb, 8lb) I was thinking of ordering the foam from US composites. My son uses alot of their products when he customizes his jet ski. Looking for your opinions.Thanks!
I did that a few years ago on my Columbia 32, I would think it would be similar for a Sabre 30. I have the original manufacturer's specs and it was the heaviest foam that US Composites offers. I forgot what it was, I seem to remember 15lb but could be wrong; I am positive it was the heaviest (and most expensive) they have. It seemed similar to the original foam that I replaced completely.

And yes, you have to do it in several layers, otherwise you get incomplete filling.
11-04-2010 07:49 PM
GaryHLucas I just rebuilt the rudder on my Etap 26 which also has a foam filled hull. I dug out the old foam and bought the 4 lb foam to replace it. That foam was very close in density to what came out of the old rudder. The foam in the old rudder was not water logged, despite a big gash in the rudder and it sat on a mooring for 25 years.

I found that you can't foam the rudder in one shot. I put a 3/4" polyethylene tube down into the rudder to about 1/3 from the bottom and poured the foam into that to get it to the bottom past the structural parts of the rudder. Then I pulled it out cleaned it off and put it in about 1/3 of the way from the top and did a second pour. I pulled it out and finished with a third pour.

Hope this helps.

Gary H. Lucas
11-04-2010 07:34 PM
mysticsailor
Foam density/Rudder repair

I'll be working on repairing the rudder on my Sabre 30 this winter. I can't find any reference on which foam density to use (there is 2lb.,4lb, 8lb) I was thinking of ordering the foam from US composites. My son uses alot of their products when he customizes his jet ski. Looking for your opinions.Thanks!

 
Posting Rules
You may post new threads
You may post replies
You may post attachments
You may edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On


All times are GMT -4. The time now is 09:34 PM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) Marine.com LLC 2000-2012

The SailNet.com store is owned and operated by a company independent of the SailNet.com forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.