SailNet Community - Reply to Topic

   Search Sailnet:

 forums  store  


Quick Menu
Forums           
Articles          
Galleries        
Boat Reviews  
Classifieds     
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Charts
Clothing
Electrical
Electronics
Engine
Hatches and Portlights
Interior And Galley
Maintenance
Marine Electronics
Navigation
Other Items
Plumbing and Pumps
Rigging
Safety
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here






Go Back   SailNet Community > On Board > Boat Review and Purchase Forum > wooden hatches on ericson
 Not a Member? 


Thread: wooden hatches on ericson Reply to Thread
Title:
  

By choosing to post the reply below you agree to the rules you agreed to when joining Sailnet.
Click Here to view those rules.

Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Topic Review (Newest First)
06-22-2006 06:11 PM
cardiacpaul I LOVE BRIGHWORK!
however, its a real pita

Cover it if you'd like, it will protect it.

No matter what the finish, if left uncovered, you're looking at a year, at best before refinishing. I'm lazy, and I'm cheap.

So, strip the finish, sand away all of it, and teak oil the pajeebers out of it.
Its cheap, east to apply, and when it starts to weather, grab some scouring powder with bleach, nylon brush it, wait for it to dry, and repeat the teak oil routine. The grain will be lovely. (repeat 2-3 times a season, just for fun)
06-22-2006 04:56 PM
jr438234606
I too have wooden hatches

My 1981 Cheoy Lee also has wooden hatches. I love the look. I refinished them to perfection with Cetol Marine Light and had custom-fitted Sunbrella fabric covers made for them. I only remove the covers when I go sailing.

john
11-05-2000 03:57 AM
Jeff_H
wooden hatches on ericson

Usually the forward hatches are the easy ones to replace. You willneed to very carefully measure the opening and the "flat". If you look at how a hatch is made, there is the a piece that gets bolted down to the deck. That piece has the actual opening which will need to be pretty close in size to the opening through your deck. This same piece has a flange that sits against the deck. This piece has an outside dimension and a bolt hole center dimension. To pick a hatch you need to make sure that the interior dimension of you deck opening is not too big or too small, that the bolts (or screws- bolts are preferable) end up passing through a solid amount of deck, and that there is a flange that is large enough for the hatch to sit on. This may require some modifications to your boat. The most probably problem will be too small a flat. Boats of that era often had a molded spigot (a raised lip that turned up inside the hatch cover). and these were typically 3/4" wide or so. Hatch bases are closer to 1 1/2" wide so you may need to either cut off the spigot and reglass where it was located, or widen the spigot which also involves some careful glass work.

There are some companies that make sliding companion way hatches, but a fit is unlikely. one thing you could do is to use your old hatch a plug and make a fiberglass mold and then mold yourself a new f.g hatch. That is not that hard to do although it takes some time to make.

I have used Bomar and Lemar hatches in the past. Bomar Hatches do not appear to have a website but Pyacht (http://www.pyacht.com/) apparently carries the entire Bomar line. Lewmar has a site, (http://www.lewmar.com/) Lewmar''s site includes a catalogue. The Sailnet Online Store may also carry both brands.In all cases you will need to send your outside, and inside dimensions to them and ask if they have a product that size since these sites do not include detailed info on product sizes.

I would take some careful measurements of the existing conditions on your boat and then look at these sources. Good luck

Jeff
11-04-2000 02:47 PM
thomaslpowell
wooden hatches on ericson

We have a 1979 Ericson 29 and love it. The hatches are wooden and look beautiful when they are refinished but this is costing more to keep up every year. I''ve had the hatches professionally refinished but the longest any of the finishes has lasted is one year. Does anyone know of a replacement hatch for my boat. Any info on manufacturers or refinishing techniques will be greatly appreciated. Thanks, Tom Powell

 
Posting Rules
You may post new threads
You may post replies
You may post attachments
You may edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On


All times are GMT -4. The time now is 01:59 PM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) Marine.com LLC 2000-2012

The SailNet.com store is owned and operated by a company independent of the SailNet.com forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.