SailNet Community - Reply to Topic
Thread: Epoxy Barrier coat Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.

User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

  Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below

  Topic Review (Newest First)
11-07-2000 03:13 AM
Epoxy Barrier coat

Putting an epoxy barrier coat over a properly applied epoxy laminate is like wrapping a plastic bag in a waxed paper bag. Depending on whose products were used and how they were applied, there are few plastic materials that are more water impermeable than epoxy resin. Un-thickened epoxies (like WEST System, MAS and System 3) work best with final overcoats of their own epoxy resin.

Putting another product over this layer is un-necessary and frankly potentially less successful.

In my opinion the only reason that the epoxy paint (which has pigments and solvents and therefore is more permeable than the resin) is added is to provide a "marker" coat so you don''t actually sand down into the epoxy resin coats. Also, Epoxy does not stand up to UV very well and so the epoxy paint coat acts as a sunshield to protect the epoxy resin should there be a time when the boat is out of the water and the raw resin is exposed.

I do question the replacement of only the gelcoat as a proper repair method. Rarely is the problem only in the gelcoat. Usually the problem is actually in the laminate below the Gelcoat. Merely replacing the gelcoat with a an unreinforced resin (or barrier coat) layer rarely solves the problem. Most qualified repair people that I have talked to seem to suggest at least a single layer of epoxy reinforced with glass cloth as a proper cure. The gelcoat layer is too thin to provide a thick enough and strong enough repair to be a permanent solution. A paint on barrier won''t change that.


11-06-2000 03:59 AM
Epoxy Barrier coat

Maybe I did not leave enough information there. The boat did have blisters several years ago and the boat was dried out and the original gel coat removed, then an epoxy "resin" coat was put on to replace the gel coat. This is like Interprotect 1000/1001 or Epiglass HT 9000 resin as recommended by Interlux. Then, as reccomended by Interlux, an epoxy paint is applied. This boat never had the epoxy paint applied, but did have the epoxy resin.
11-05-2000 06:31 PM
Epoxy Barrier coat

What is Interprotect but an epoxy layer? It sounds like whatever epoxy was put on your hull simply doesn''t have a fancy marketing name. Despite fancy names and advertising, epoxy (like gasoline) is epoxy. If you''ve got a layer of it, it doesn''t matter who made it. If there aren''t any blisters now in a 1981 boat, it sounds like you''re trying to fix a problem you don''t have. Get some new sails instead, you''ll have more fun.
11-05-2000 06:28 AM
Epoxy Barrier coat

I am looking into purchasing a 1981 Ericson 38 which apparently (and confirmed on inspection) has no blisters because of a previous gel coat job where it was removed and replaced with an epoxy layer but never given an epoxy barrier coat like Interprotect 2000E/20001E. It has bottom paint directly on the epoxy. I believe this needs to be applied as soon as possible, but the antifouling was just put on new. Does anyone out there have an opinion on this? Should the new antifouling be immediately removed and the barrier coat applied or should one wait a year till the bottom paint needs to be redone and do it then? How urgent do people believe this is? The epoxy job was done about three years ago.

Steve Morrell

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

For the best viewing experience please update your browser to Google Chrome