|Topic Review (Newest First)|
|12-08-2011 01:47 PM|
Originally Posted by BELLATRIX1965 View Post
Really, the load on the windlass should not be great if a proper chain stopper is used. That is where the big snatch loads are.
|12-07-2011 09:37 AM|
Originally Posted by BELLATRIX1965 View Post
|12-07-2011 09:32 AM|
|BELLATRIX1965||Can anybody recommend a good source for G10 plate? Preferably about 5/8" thick, and maybe about 12" by 12" size? Just need a backing plate for an anchor windlass - not a full sheet of the stuff!|
|12-07-2011 09:01 AM|
Any of the HDPE products lack the stability to prevent flex and properly "back", unless VERY thick. The ability for anything, even 5200, to stick to them for long is what really makes them a poor choice though..
I had a customer use 3/4" HDPE for backing plates, Sea Board (same as Starboard) and in one season 3 out of 7 were known to be leaking. They provided no support and the flexing when turning the handles cause the seal to leak.
A small batch of boat builders tried this over the years, mostly small power boat builders, and I suspect also ran into problems. At the last boat show I did not see any of them using it for backing blocks any more, even ones I'd recalled seeing in the past... HDPE is very flexible and you might as well be trying to bed a Teflon frying pan, sealant wise... Nothing really stocks to it...
Leave the cutting boards in the galley and use known time tested and proven methods below water to keep your boat from sinking or leaking...
Of course you don't need to take my advice here's what the manufacturer says:
"King StarBoardŽ, King StarBoardŽ ST, King ColorCoreŽ, King ColorBoardŽ and King CuttingBoardŽ can not be glued using standard adhesives. Products like 3M’s 5200 work well as a water sealing caulk but will not adhere King StarBoardŽ to itself or other materials in a permanent bond."
|12-07-2011 08:29 AM|
|jacob30||McMaster Carr sells a 12"x 12" 3/4" thick fiberglass sheet for $30. I just used it for my backing plates. So far worked great. Search GPO3 for the part.|
|12-07-2011 12:22 AM|
I partially agree with the above - plywood is better than solid wood. But the backing plate, whatever it is made of, should be on the underside of the deck, not the liner as there is a gap between the liner and the deck. Tightening the bolts will move the liner closer to the deck. I would try to get the backing block right under the deck.
As far as epoxying the backing block to the deck, or the inside of the hull in the case of a through hull, I think it is the best idea as it will become part of the hull or deck, strengthening it a great deal.
For through hull installation, see this link: Replacing Thru-Hulls and Seacocks Photo Gallery by Compass Marine at pbase.com
And fiberglass or G10 is ideal. What I do is save any fiberglass scraps I remove from any boat - mine or others as I work on boats - and cut backers from them for my use. Any boatbuilder should have offcuts as well, probably free for the asking.
|12-07-2011 12:05 AM|
I wouldn't use cutting board, or any other plastic, for a backer plate. Plywood is easy to work and lasts a pretty long time.
Solid stock is not a good idea if you are considering using wood. The cross lamination of the grain in plywood is preferred, it won't split and doesn't have internal tension like a piece of oak. I use 3/4" marine ply for through-hulls and I soak them in Smith's epoxy at least twice. I wouldn't epoxy to the hull, as the washer will be removed when the thru-hull is next replaced. Hopefully after I don't own the boat anymore.
|12-06-2011 11:47 PM|
I'm about to add backing plates myself. G10 was recommended and it certainly makes sense but I was thinking about hardwood oak for convenience and cost. Home depot sells 0.5"x6"x4' for $13 that would make several plates. Also in my boat many of these backing plates would be visible and stained oak would blend in nicely.
How much advantage is there to epoxying to the hull? I don't like permanently attaching anything and second, I think I have an interior liner that would make this less useful?
|04-09-2011 07:08 PM|
|Baywind||I got a used SS sheet that was a toe kick off a door at a building for free. I cut it with my grinder and then sand the edges smooth and corners round. It is tough to drill the holes but it is strong and looks good.|
|04-09-2011 07:38 AM|
|DonScribner||Cutting boards are usually HDPE (High Density PolyEthylene). If you are interested in using a plastic, use UHMW (Ultra High Molecular Weight polyethylene). It's more expensive but still affordable in the sizes that you would require. We shim skylights weighing many tons with the stuff. It is available, among other places, at McMasterCarr.com|
|This thread has more than 10 replies. Click here to review the whole thread.|