SailNet Community - Reply to Topic

   Search Sailnet:

 forums  store  


Quick Menu
Forums           
Articles          
Galleries        
Boat Reviews  
Classifieds     
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Charts
Clothing
Electrical
Electronics
Engine
Hatches and Portlights
Interior And Galley
Maintenance
Marine Electronics
Navigation
Other Items
Plumbing and Pumps
Rigging
Safety
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here






Go Back   SailNet Community > On Board > Gear & Maintenance > Thru-Hull Thread count
 Not a Member? 


Thread: Thru-Hull Thread count Reply to Thread
Title:
  

By choosing to post the reply below you agree to the rules you agreed to when joining Sailnet.
Click Here to view those rules.

Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Topic Review (Newest First)
04-27-2011 11:09 AM
DrB
It's in

Thanks all for the responses. It' turns out, no pun intended, that I had >6 but <8 full turns before I reached tightness. I am confident that I have enough NPS thread into the flange to insure a good seal and one that won't easily unthread. Before I threaded it in, I cleaned the hole well with lots of OMS and Acetone, allowed to dry and then coated the inside of the hole with a layer of 291. Then I gooped up the threads of the thru-hull, threaded it in and really snugged it down.

Next week, when I get splashed, will be the test.

DrB
04-26-2011 09:17 PM
eherlihy ...And the reason that they make through hulls with NPS fittings is so that you can cut the through hull fitting to the correct length, and still screw the fitting into the adapter, or flanged seacock.
04-26-2011 09:09 PM
eherlihy I'm in awe of Klem's 2nd paragraph...

However, using a NPS thread - like on the through hull - in an NPT fitting - like on an unflanged seacock - only allows 3 turns. I know this because that is what the yard mechanics did with the sink through hull on my boat before I purchased the boat and fixed it.

Maine Sail has posted a good illustration of this problem here.
04-26-2011 08:01 PM
bwindrope I'm no ME and don't portray one on TV, and can only add that the Groco IBVF flanges I just installed on my boat are designed to mate to Groco thru-hulls and IIRC they accept about 6 turns before topping out. Same for the Groco ball valves that are designed to fit the IBVF flanges on top. About 6 turns.

I don't know squat about the technical specifications of the situation, but trust that Groco does and that this thread fit is sufficient for full strength in their bronze. Just a data point for consideration.
04-26-2011 06:33 PM
klem There are rules of thumb for the required thread engagement but most of them are for coarse threads in hardened steel nuts so they do not apply well here.

The correct way to do this would be to figure out what the thread stress area is (it is a function of the diameter and pitch as well as number of threads and can be easily looked up in Machinery's Handbook). Then, you can look up the mechanical properties for the seacock and nut material (note: both need to be strong enough). Multiplying the stress area by the yield strength of the material will give you an axial force which can be transmitted. When you do this calculation for a fastener, it is straight forward since you just need to make the threads stronger than the rated yield strength of the fastener. For a thru hull, the same is true except that knowing the strength of the thru hull is a bit tougher (although a force/area approximation is a good start). Additionally, it is always wise to check the induced tension from tightening the nut and make sure it is below the thread yield strength and overall fitting strength. There are many online calculators that will let you figure this out, you just need the diameter and tightening torque.

Since this is a marine environment, you are going to want to leave yourself a significant factor of safety. There really is no excuse not to, it won't add a lot of weight. The marine environment has the unique ability to corrode or otherwise degrade just about anything which will greatly impact the strength. In addition, the normal fatigue assumptions about a bolted joint do not apply very well here because the fastener (thru hull) is stiffer than what it is clamping together.

Sorry that I didn't give you a number answer, there are too many variable. It will give you a place to start (or maybe just convince you to buy the longer ones).
04-26-2011 06:22 PM
WDfrmTN If it helps, for aircraft and general mechanics, three threads beyond a bulkhead nut is sufficient.

Here is an article that might help: Installing a Seacock by Don Casey
04-26-2011 04:25 PM
DrB
Thru-Hull Thread count

A standard mushroom 3/4" thru-hull has 2 inches of threads. Based on the thickness of my hull and base mounting plate for the seacock, I estimate count that the I can get 6 full turns before the thru-hull is flush with the hull and therefore can not be turned anymore. I would need to purchase the Long version if I wanted more. The seacock flange will allow 12 full turns before it bottoms out.

Here is the $64,000 question, do I need more threaded turns or is 6 adequate? If 6 is okay, what is to few? I was told in my youth that if you can at least 4 full turns, you have reached essentially the strength of the thread and more turns doesn't buy significantly more strength. T or F? There is adhesive on the threads too.

Any machinists, Mech E or generally smart people care to weigh in?

Thanks.

DrB

 
Posting Rules
You may post new threads
You may post replies
You may post attachments
You may edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On


All times are GMT -4. The time now is 02:50 AM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) Marine.com LLC 2000-2012

The SailNet.com store is owned and operated by a company independent of the SailNet.com forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.