|Topic Review (Newest First)|
|10-29-2011 10:33 PM|
I forgot to mention my deal. Asking was $26,500. We landed at $23,000. following the survey.
The tank, rudder shoe and the potential soft spot around the through hulls made that possible. The owners lived on the other side of the state and I think didn't want the hassle of traveling back and forth to show it etc. We were close so they made it work.
|10-29-2011 10:23 PM|
My survey was pretty good. No spongy decks as I believe they are not cored, but solid. At least that was what I read and after the survey believe. My boat has a cluster of through hulls in the head. The surveyor's hammer didn't have that crisp sound when it landed in the middle of them. That was this spring
When I haul for bottom paint next spring, I'll check it closer. Inside it sounds fine. The only penetrations I need there are for the head sink and the speedo so I may have the others filled in.
My boat has a porta pottie. I'll be darned if I can see where a holding tank would go. All the seacocks are the old tapered Wilcox Crittenden type. Those will be replaced over time. They all work, but don't have handles and they need to be serviced often.
My steel fuel tank needed replacing as a result of the survey. One corner was damp. No dripping of fuel though. I had an aluminum tank built as I couldn't find an off the shelf tank that would work.
The only other thing was a well worn rudder shoe bushing. It is just sloppy and the rudder may be rubbing on the shoe. Again this will be a spring haulout project. I have found two Seattle yards that know what I'm talking about and can do the work. I have also read of a repair using a bronze or brass filled epoxy. That may be an option too.
That was about it. We really are loving her more every time we go out. Backing is an adventure, but that is a design thing shared by many of her type.
|10-29-2011 05:00 PM|
|bandaidmd||Did your survey turn up any major issues like spongy decks? if you don't mind saying what kind of deal did you get. this is one of the boats on my shopping list.|
|10-12-2011 09:57 AM|
|jb1528||Thanks for that suggestion. I did that recently after seeing a 32 moored in Monterey CA. The owner was happy to hear his boat was safe and secure.|
|10-11-2011 12:13 AM|
Originally Posted by jb1528 View Post
|10-10-2011 11:20 PM|
Originally Posted by jb1528 View Post
|10-10-2011 10:56 PM|
That is very cool. How much wind was there? Did the Beneteau pass you?
I'm thinking 17-18 apparent is about the comfortable limit before reefing. Sound about right?
|10-10-2011 08:15 PM|
|MarkSF||Yesterday we held our own for a while against a C36, on a beam reach in 17-18 kn. apparent. Based purely on LWL, the Cat should have been a knot faster.|
|10-10-2011 07:52 PM|
|Dcneuro||I was sailing back to our yacht club very hard on the wind with an 04 benneteau 343 right behind me. I had always assumed they could point higher then my Bristol 32. Perhaps they can, however, so much ground was lost to leeway that my boat actually outpointed the benneteau!|
|08-04-2011 07:24 PM|
I posted earlier that I wanted some input as to the performance of Bristol 32s.
I have to tell you that I am now very pleased after finally getting some air over the sails of my '75.
The other evening, after setting my crab pot and with just the headsail up in about 18 apparent I hit 7 through the water on maybe a quarter reach. The next evening with both sails and about the same wind, I hit 7.5 for a moment.
Soft ride, solid, healing a lot. I loved it. I also reduced the headsail and still made 6.5. I am still experimenting. I have a fairly two year old North main with a full top batten and standard lower battens. The genny is a year older.
I love it.
|This thread has more than 10 replies. Click here to review the whole thread.|