SailNet Community - Reply to Topic
Thread: Raymarine Autohelm/Pilot ST4000 Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.

User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

  Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below

  Topic Review (Newest First)
06-04-2014 03:53 PM
Re: Raymarine Autohelm/Pilot ST4000

Capt. Dan:
I just posted a problem with my ST4000+. You may be able to help.
The head always reads 50 Deg. I disconnected the wires from the Fluxgate at the head and reconnected. Not help. I will disconnect and measure the resistance per the manual. Any thoughts or suggestions?
11-15-2013 06:16 AM
Andrew Thompson
Re: Raymarine Autohelm/Pilot ST4000

Dan, thanks - had a look inside the motor/gear casing and can see what to do now. All I need now is a controller of some kind to drive the thing.....

Thanks for your help, much appreciated

11-13-2013 09:15 PM
Re: Raymarine Autohelm/Pilot ST4000


To convert to a 2 wire, remove the small circuit board on the back of the motor. Solder two wires to the tabs on the motor and you are done.
11-13-2013 11:36 AM
Andrew Thompson
Re: Raymarine Autohelm/Pilot ST4000

Hi Brewgyver

Thanks! We have a 40 year old Fisher 30 - a very sturdy motorsailer. When she was built she would have been considered a large yacht and she is still capable of squashing some of the newer bigger but lighter boats as she weighs in at around 7.5 tons laden. Sailing here has been good this year but the gales are just starting to get a bit too frequent - another gale warning just broadcast.

I must post a profile picture showing the boat.

All the best

11-13-2013 11:31 AM
Re: Raymarine Autohelm/Pilot ST4000

Originally Posted by Andrew Thompson View Post
Thanks Faster - I'm trying to build up my posts but only if I have something useful to contribute!


Speaking of posting more.... a friend of mine sails a Fisher 25. We all sail on the Columbia River in Portland, OR.
Fishers are quite rare around here.
I've been out for a sail and was impressed at how much boat interior there was and how solid it felt. Takes quite a bit of wind to move it, though, and pointing is not what it likes....

Anyhow, do contribute when you can. Everyone has something to add! (Well, almost everyone...!)


ps: I used an Autohelm 4000S on my current boat for a decade, and then upgraded to a Raymarine X5. The software is supposed to be better, but I do not see any obvious changes in the hardware quality...
11-13-2013 11:21 AM
Re: Raymarine Autohelm/Pilot ST4000

Andrew, to help with your post count, what do you sail, and how is the sailing in your part of England?
11-13-2013 09:43 AM
Andrew Thompson
Re: Raymarine Autohelm/Pilot ST4000

Thanks Faster - I'm trying to build up my posts but only if I have something useful to contribute!


11-13-2013 09:34 AM
Re: Raymarine Autohelm/Pilot ST4000

Andrew.. from what I understand Dan is very helpful (and knowledgeable) with this sort of thing.. once you get a few more posts you might send him a PM if he doesn't notice the resurrection of this thread. I think his email is somewhere on this board too...
11-13-2013 06:25 AM
Andrew Thompson
Re: Raymarine Autohelm/Pilot ST4000

Dan, hi. I saw your post (from last year) about the conversion of a four wire Autohelm motor to two. I have one of the old compass rose type AH3000 from which I want to use the motor on another pilot controller - not sure which yet. I've identified that the red and blue wires will drive the motor fwd or reverse, but don't quite get the yellow and green, other than measuring that they sit at around 4v when the pilot is not turning the motor and (depending on rotation) 8v or 4 v when it is. Wondered whether they were either feedback or damping in some way?

I'd really appreciate your advice about what the wires do and how to convert.

Many thanks

Andrew Thompson, Fisher 30 "Jojac"

Originally Posted by CaptainDan99 View Post
If you have the analog 3000, the one with a compass rose on top with red & green lights, it uses 4 wires to the motor. You can convert it to a two wire easily if you are handy with soldering. You would also need to add a plug to the motor wire to attach to the control head. The 3000 and ST3000 heads can usually be found on ebay or maybe in a local used marine store. Email me if you need more info about the 4 wire conversion.
02-01-2012 02:01 PM
Ritchard Here's an ST4000 for sale near me if anyone is interested:

Raymarine Autohelm 4000+ autopilot - Ontario Parts, Trailers, Accessories For Sale - Kijiji Ontario Canada.

Santa brought me a Smartpilot X5. I have to get around to mounting it, and first deciding what to do with/where to install the display.
This thread has more than 10 replies. Click here to review the whole thread.

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

For the best viewing experience please update your browser to Google Chrome