SailNet Community - Reply to Topic
Thread: Teak Rub-rail Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.

User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

  Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below

  Topic Review (Newest First)
06-17-2011 10:16 PM
arf145 This is a rubrail, screwing into the side of the hull? Or maybe I don't have the correct picture. But if it isn't screwing into cored hull, I don't see why the whole drill-out, epoxy, redrill process is necessary.
06-17-2011 03:55 PM
RichH If you dont seal the rub strake to the hull, water will accumulate between the two and will eventually permeate through the wood and thus turn it 'dark/black' must faster. Also trapped moisture 'behind' the wood will especially cause the coating to begin to 'lift' at the margin of the wood nearest the hull. Very best is to 'encapsulate' the strake with epoxy on the side that touches the hull, then affix to the hull with 'caulk'.

Simple answer: seal it, standard "Life Cauik" that is 'colored' (teak, mahogany, etc.) will work best and will be the 'least obvious'.
06-17-2011 01:26 PM

It isn't necessary to seal the rub rail to the boat but can help with keeping growth like mildew from getting a hold there. I have a full teak deck and the only place I have any problem with mildew is the edge where the teak meets the fiberglass.

The other suggestions on sealing the screw holes are excellent ones.
06-17-2011 09:32 AM
butyl tape

I like butyl tape for many applications but believe the correct and best way to deal with the fasteners if the core is dry is to drill them out oversized, fill with apoyy like west system etc, then re-drill and install screws. If leaks around screws were to happen (definate posibility on flexing deck) any water would not be able to migrate / wick into core.

Captain Michael
06-17-2011 09:18 AM
arf145 Someone else can give the definitive answer but, 1) don't use silicone, whatever you use, 2) those are probably bronze screws, not brass, 3) if the screws are penetrating the fiberglass at all, I'd at least seal around the screws. I'd use butyl tape.
06-17-2011 09:02 AM
Teak Rub-rail

Refurbishing a 69' Highlander with a teak rub-rail. Teak came out good after sanding and refinishing. Going to purchase new fastners to finish off the look. Question is do i use any type of sealant (silicone?) on the top and bottom of the rail where it meets the fiberglas body? I assume there would be no adhesive on the back-side of the rail being that it has about 20 brass wood screws down the length of the boat. It didn't look like there was any adhesive or sealer on the back-side of the rail when I took it off but it could have disappeared with age.

Thanks for the help!!!

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

For the best viewing experience please update your browser to Google Chrome