SailNet Community - Reply to Topic

   Search Sailnet:

 forums  store  


Quick Menu
Forums           
Articles          
Galleries        
Boat Reviews  
Classifieds     
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Charts
Clothing
Electrical
Electronics
Engine
Hatches and Portlights
Interior And Galley
Maintenance
Marine Electronics
Navigation
Other Items
Plumbing and Pumps
Rigging
Safety
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here






Go Back   SailNet Community > On Board > Gear & Maintenance > Electronics > Raymarine X-5
 Not a Member? 


Thread: Raymarine X-5 Reply to Thread
Title:
  

By choosing to post the reply below you agree to the rules you agreed to when joining Sailnet.
Click Here to view those rules.

Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Topic Review (Newest First)
08-10-2011 06:37 PM
tdw
Quote:
Originally Posted by Cptken View Post
Every time you secure power the X5 resets to a response level 5. Part of my leaving the dock checklist is to push the standby button until the response screen, then use the -1 button to reset it to 2 or 3 depending on the conditions. Really cuts down on the amount of self correction.

In the setup menu there is a way to change the default response level. I don't have manula with me so cannot give you exact details but if you run through setup in the manual it will show you how.
08-10-2011 01:43 PM
Cptken Every time you secure power the X5 resets to a response level 5. Part of my leaving the dock checklist is to push the standby button until the response screen, then use the -1 button to reset it to 2 or 3 depending on the conditions. Really cuts down on the amount of self correction.
08-09-2011 06:58 PM
tdw
Quote:
Originally Posted by kymnlin View Post
"We have an X5 on the old girl. "

Hi, what size is " the old girl" I am trying to decide if the X5 Will work on my 30ft Spencer it is about 4 tonne laden and a bit touchy down wind. The old st4000 after many hours of use and all most as many in the workshop at home being fixed has gone completely dead. It could not keep much of a course down wind in a 2 meter chop! Hoping the X5 would be better?

cheers

Alices venture
The old girl is a 34' Van de Stadt sloop, aka Silver Raven. My guess would be that we displace a couple of tonnes more than you so you should be fine. X5 max displacement is 7.5 tonnes. We are around 6.5t off the plans though I'd reckon we are probably closer to seven fully loaded.
08-09-2011 12:14 PM
olson34
X-5 autopilot notes

Yesterday we did the "Learning" final step for the new AP and it Passed.
It is interesting to turn the control over to the AP and let it wander the boat in both directions while doing this. Took two tries when we started running out of room on one side of the river the first time. You really do need about a quarter mile of open water, front and both sides when commencing this part.

Looking back, the oddest part of the install was the need to reverse the polarity for the power to the motor drive. Our dealer said we might have to do this and he was right. Another boat in our moorage found the same problem when he did the same install a month ago. The Raymarine book is informative otherwise, but this should have been covered better.

Cheers,
LB

ps: I would have reported back sooner, but I lost a week on some pesky engine maintenance stuff what resulted in a whole new entry on my blog over at EY.org. (Sigh...)

pps: our boat is a 34 foot sloop that displaces about 11K pounds in light-load trim, if that helps anyone interpreting AP specs.
08-09-2011 09:51 AM
kymnlin "We have an X5 on the old girl. "

Hi, what size is " the old girl" I am trying to decide if the X5 Will work on my 30ft Spencer it is about 4 tonne laden and a bit touchy down wind. The old st4000 after many hours of use and all most as many in the workshop at home being fixed has gone completely dead. It could not keep much of a course down wind in a 2 meter chop! Hoping the X5 would be better?

cheers

Alices venture
07-27-2011 07:18 PM
tdw We have an X5 on the old girl.

Polarity thing is a good possibility. If that does not work check the positioning of your fluxgate. I had the same problem with the whole learning thing and it turned out to be the fluxgate position.
07-27-2011 07:01 PM
f182 We just replaced our old 4000 series with X5 GP tiller pilot took a few circles to swing the compass.
The auto learn went well under sail in 15knts just reaching in a 1.5m swell. Passed our auto learn by step 10.
Compared to the old pilot the X5 with gyro holds course very well in all conditions.
The pilot had a hard break-in period as the first 2 day of use we did two 180Nm days broad reach to square running poled out in 25 to 35 kntots and a combined sea and swell of up to 6m.
The old pilot would be driving very hard full lock prt to stb squared running but the new X5 just held course.

Great bit of kit.
07-27-2011 03:30 PM
olson34
Raymarine X-5

I just finished the install yesterday. This replaced an old A4000S.
After going thru the initiation circle-turning, I tried the "learning" sequence, but it did not "pass". Dealer asks that we try it again, after correcting the motor polarity... and we will do so tomorrow.
No problem with doing so, and the dealer will do whatever it takes to make it right.
My question is more about other sailors' experiences with this unit. I figure that since it's been out since '08 (?) the bugs should be out by now.

So any anecdotal stuff/trivia would be interesting.

TIA,

LB

 
Posting Rules
You may post new threads
You may post replies
You may post attachments
You may edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On


All times are GMT -4. The time now is 08:11 PM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) Marine.com LLC 2000-2012

The SailNet.com store is owned and operated by a company independent of the SailNet.com forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.